Mahindra ML170 series Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 79

background image

17

3.2. MOUNTING KIT INSTALLATION

3.2.1. Position the tractor and loader on a hard level surface under a hoist.

3.2.2. Remove front weights from tractor.

IMPORTANT: Do not tighten any hardware until all components are attached onto the tractor.

CAUTION: Lift and support all loader components safely.

3.2.3. Check right hand side of tractor in front axle
area. Reposition components as shown so they will
clear loader bracket.

Reposition components

3.2.4. Position hoist with chain through center bracket
hole to support bracket during installation.

Position hoist with chain

through this hole when

mounting center bracket.

3.2.5. With hoist supporting center bracket, locate
oscillation stop with tab under and toward front of
tractor and 1/2" thick 4-hole spacer between center
bracket and tractor. Install 16mm x 2.0P x 90mm hex
bolts Grade 10.9, 5/8" lockwashers, and 5/8"
flatwashers, 4 places. Do not remove hoist.

Oscillation Stop

Spacer, 4-Hole

16mm x 2.0P x 90mm Grade 10.9 Hex Bolt,

5/8" Lockwasher, and 5/8" Flatwasher,

4 places.

Center Bracket

«
...
16
17
18
19
20
...
»

Содержание ML170 series
















































































Отзывы:

Нет отзывов

Похожие инструкции для ML170 series

Бренд: Douglas Dynamics Страницы: 10

Бренд: Daedong Страницы: 111

Бренд: Troy-Bilt Страницы: 113

Бренд: Cub Cadet Страницы: 61

Бренд: Hagie Страницы: 102

Бренд: Land Pride Страницы: 26

Proxima Plus 90

Бренд: Zetor Страницы: 34

Бренд: Zetor Страницы: 220

Бренд: Valtra Страницы: 36

Бренд: Husqvarna Страницы: 304

Wheel Horse 79361

Бренд: Toro Страницы: 28

Бренд: Summit Страницы: 35

Grain Belt Plus

Бренд: Honey Bee Страницы: 179

Grain Belt Plus 3055

Бренд: Honey Bee Страницы: 253

Бренд: Gehl Страницы: 202

Бренд: Full Boar Страницы: 17

Heritage RS 14/82

Бренд: AL-KO Страницы: 22

Mini Tracker 506

Бренд: Artec Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды