Mahindra 10 Cab Series 4510C Скачать руководство пользователя страница 100

Страница: 100 / 115

Fill the tank and bleed the fuel
system

Contact dealer for repair

Lack of fuel

Faulty injectors

Seized engine due to lack
of oil, the wrong oil or
lack of coolant

The engine stops suddenly

Engine

Refill with coolant

Adjust or replace

Clean or replace air filter

Clean the core

Replace the oil to correct grade

Lack of coolant

Broken or misadjusted fan
belt

Clogged air filter element

Clogged radiator

Low oil

The engine overheats

Contact dealer for repair

Poor fuel injection

Faulty injection pump

Wrong valve clearance

Wrong idle setting

Faulty injector

The engine stops at low
revolution

Bleed the system

Clean or replace both filters

Fill tank or turn tap on

Contact dealer for repair.

Air in fuel system

Clogged fuel filter

No fuel being supplied

Glow plug disconnected
or not working

Starter operates OK but
does not start the engine

Charge the battery

Clean the earth lead and tighten

Drain and replace with correct
oil

Low battery

Bad earth

Thick oil

Starter operates but not
enough to turn the engine

Push the clutch in

Charge or replace the battery

Dealer to repair or replace

Contact dealer for repair or
replace

Clutch not pushed in

Battery flat

Switch faulty

Turning the main switch
will not operate the starter

Bleed the system

Contact dealer for repair.

Air in the fuel system

Faulty injector

Fuel pipe leak

Engine revolutions are
irregular

REMEDY

CAUSE

SYMPTOM

FAULT TRACING

Содержание 10 Cab Series 4510C




















































































































Результаты поиска

Содержание 10 Cab Series 4510C

Отзывы:

Похожие инструкции для 10 Cab Series 4510C

Бренды по названию

Популярные бренды

Mahindra 10 Cab Series 4510C, Руководство оператора

Результаты поиска

Содержание 10 Cab Series 4510C

Отзывы:

Похожие инструкции для 10 Cab Series 4510C

Бренды по названию

Популярные бренды