MAGUIRE Weigh Scale Blender Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 141

background image

M A G U I R E P R O D U C T S , I N C .

30

W E I G H S C A L E B L E N D E R



Normal Operation and Saving the Configuration

1.

Fill HOPPERS: REGRIND, NATURAL, COLOR, ADDITIVE in hoppers as labeled. If auger feeders are used
COLOR is the RIGHT side feeder and ADDITIVE is the LEFT side feeder.

2.

Set THUMBWHEEL switches for percentage of materials desired:

REGRIND

enter as a percentage of the entire mix

– no decimal place (xx%)

COLOR

as a percentage of the Natural (xx.x%)

ADDITIVE

as a percentage of the NATURAL (xx.x%)

3.

On Controller, turn POWER ON, set STOP, and PAUSE switches UP. Switch MIXER motor DOWN to run for
a timed period each cycle.

Unit will now operate automatically to maintain a level of material high enough to cover the sensor.

Use the STOP or PAUSE switches to stop the dispensing of material. Turn POWER off only on final
shutdown. Battery-backed RAM ensures all information is retained even with power turned off.

The KEYPAD is only for:

1. MANUAL TESTING.

2. ALTERATION of INTERNAL PARAMETERS

After several days of proper operation:

Save all parameter information to the User Backup Settings for future retrieval just in case software
problems develop later.

To SAVE all parameter information to the User Backup Settings:

Save Parameters Keypad Sequence:

Press

Display will say:

ENTER PASSWORD

Press

Display will say:

PROGRAM

Press

Display will say:

INSTRUCTION [ __ ]

Press

Display will say:

SAVE USER SETTINGS

Wait: when done, Display will say:

PROGRAM

Press

Display will say:

WAITING

If software related problems develop later, RETRIEVE this correct copy of the parameters from the User
Backup Settings. This clears corrupted data from RAM and corrects most software problems.

To Retrieve:

Retrieve Parameters (CLEAR) from User Backup Settings - Keypad Sequence:

Switch

Power Off to the Controller

Hold

Hold th

e “CE” Key down

Switch

Power on to the Controller

Release

The

“CE” Key

Display will say ***

CLEAR

***

If you do not see

CLEAR

on the display, do it again.

«
...
28
29
30
31
32
...
»

Содержание Weigh Scale Blender














































































































































Отзывы:

Нет отзывов

Похожие инструкции для Weigh Scale Blender

Бренд: Varec Страницы: 74

Бренд: Halyard Страницы: 84

Бренд: PAIDI Страницы: 48

Бренд: Canta Страницы: 2

Бренд: Nemco Страницы: 13

Бренд: Ecco Страницы: 12

Бренд: UMF Medical Страницы: 12

Sportsound SSR-300

Бренд: Daktronics Страницы: 42

Бренд: Ecler Страницы: 108

Бренд: R&S Страницы: 121

Бренд: Federal Signal Corporation Страницы: 4

Бренд: FASTERHOLT Страницы: 96

Бренд: Gardner Bender Страницы: 8

Бренд: NARIKA Страницы: 2

Бренд: Varytec Страницы: 5

Бренд: Saab Страницы: 98

Бренд: Kaixin Страницы: 89

Бренд: Omlet Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды