MAGUIRE Weigh Scale Blender Скачать руководство пользователя страница 108

Страница: 108 / 141

M A G U I R E P R O D U C T S , I N C .

108

W E I G H S C A L E B L E N D E R



Updating Controller Firmware

Updating the firmware within the 12-12 Controller can be accomplished through 2 different methods.

Method 1: USB Drive Update

1. This method uses a standard USB drive. There are 3 files that are required to perform a software

update to the 12-12 Controller. These files may be requested from Maguire Products and are
labeled:

UPDATER.BIN
912WFxxx.crc
912WFxxx.s28

When you are provided with these three files, they should be copied to a USB drive and placed in a
folder named:

Maguire

2. Insert the USB drive into the USB port on the 12-12 controller. Note, the controller should be

powered on but should not be running cycles.

3. Enter into program mode. Press 22222

4. Press 93. The display should say

Checking Device

…

5. If more than one firmware version is stored on the flash drive, Press to toggle between firmware

versions. If you only have a single copy of firmware stored on the flash drive the controller will default
to displaying that version.

Select Version:
WFxxxxx

6. When the firmware to loaded is displayed, press the

key to begin the firmware transfer.

Verifying: [WFxxxxx]

▒ ▒ ▒ ▒ ▒ ▒ ▒ ▒

Updating: xxx/726

▒ ▒ ▒ ▒ ▒ ▒ ▒ ▒

Do not turn off controller or remove the flash drive while firmware
is updating! Doing so may corrupt the controller’s firmware.

7. When

Update Complete!

is displayed, turn off the controller and turn on again.

Clear All

will display

if a version update was applied. The firmware update to the controller is complete.

Содержание Weigh Scale Blender














































































































































Результаты поиска

Содержание Weigh Scale Blender

Отзывы:

Похожие инструкции для Weigh Scale Blender

Бренды по названию

Популярные бренды

MAGUIRE Weigh Scale Blender, Установка, эксплуатация и обслуживание

Результаты поиска

Содержание Weigh Scale Blender

Отзывы:

Похожие инструкции для Weigh Scale Blender

Бренды по названию

Популярные бренды