background image

Maguire Products, Inc. 

 

34 

MLS Clear Vu

 

 

– General Information 

 

MLS Clear Vu Features 

 

VACUUM UNIT: 

The ring compressor vacuum power unit is QUIET, RELIABLE, and LONG LASTING.  A 
single power unit supplies 8 stations, keeping costs low. 

 

POSITIVE OPERATION OF VALVES: 

All valves are positively operated by air cylinders.  There are no weighted flaps that 
might not close properly.  Valves close with a sliding action so "Static cling" pellets are 
wiped clear. 

 

STROBE LIGHT and audible ALARM: 

STROBE LIGHT and audible ALARM activate whenever a load cycle does not satisfy 
the sensor. 

 

STATION ALARMS: 

On total system power up, or after turning power on for a given station, the "alarm" 
function for that station is not active.  Filling the hopper for the first time, and covering 
the sensor, activates the "alarm" function for that station. 

 

After this "full hopper" initialization, the alarm will sound if the sensor is not immediately 
satisfied after a load cycle. 
 
Alarms may be selectively disabled for each station. 

 

ALARM SILENCE BUTTON: 

The silence button silences the alarm until any new event starts it up again.  The 
covering of the sensor of an alarming station will also silence the alarm, (unless another 
station is also in an alarm state). 

 

STATION TIMERS: 

Each receiver has a LOAD TIME associated with it.  Initial default load times are 10 
seconds and may be altered using the "SET LOAD TIME" button. 

 

SET TIMERS BUTTON: 

A TIMER button is provided as an input to the processor.  During any single load time, if 
the button is pressed, the loading time will continue to run until the button is released.  
When released, the station will stop loading immediately.  The time of release 
establishes the NEW load time for that station. 
 
One button serves to set times for all stations. 

 

FILTERLESS RECEIVERS: 

Individual receivers are filterless.  A central dust filter protects the blower unit.  This 
eliminates the need to service filters on top of hoppers and places the only filter in easy 
reach. 

 

EXPANDABLE UP TO 16 RECEIVERS: 

Your controller can control up to 8 receivers.  However, additional controller can be 
"linked" to your first controller using the Dual Controller Option, allowing up to 16 
receivers to operate off one single vacuum pump. 

Содержание MLS Clear Vu







































Отзывы: