manualshive.com logo in svg

Magtrol 6400, Руководство пользователя, Страница: 28 / 56

Поделиться
Скачать
Magtrol 6400 Скачать руководство пользователя страница 28

19

Magtrol Model 6400 Torque Transducer Display

Chapter 4 – Manually Controlled Operation

OPERA

TION

4.1.6

I

NPUT

/O

UTPUT

 (I/O) P

ARAMETER

 S

ETUP

Sets up GPIB (IEEE-488) address, serial (RS-232) baud rate and display contrast.

1. Press and release SHIFT.

2. Press and release SETUP.  "MENU: SYSTEM" appears in the display.

3. Press and release UP 

S

 button twice.  "MENU: I/O appears in the display.

4. Press and release SHIFT.  The Contrast Setup Menu (as seen in Figure 2–2) appears.

5. Use UP 

S

 and DOWN 

T

 buttons until desired contrast level is displayed.

6. Press and release SHIFT.  The display appears as follows:

POWER/AUX

TORQUE

SPEED

Figure 4–15  GPIB Address Setup Menu

7. Use UP 

S

 and DOWN 

T

  buttons until desired GPIB address is displayed.  Select from a

range of 0 to 15.

8. Press and release SHIFT .  The display appears as follows:

POWER/AUX

TORQUE

SPEED

Figure 4–16  RS-232 Baud Rate Setup Menu

9. Use UP 

S

 and DOWN 

T

 buttons until desired RS-232 baud rate is displayed.  Select  from

300, 600, 1200, 2400, 4800, 9600 and 19200.

10. Press and release SHIFT to exit and return to main menu.

4.2

USING INTERNAL MEMORY

4.2.1

S

TORING

 D

ATA

 P

OINTS

1. Press and release STORE button.  The display will indicate STORE followed by a number.

POWER/AUX

TORQUE

SPEED

Figure 4–17  Store Display

This display indicates the memory location that contains the data.

Содержание 6400

























































Отзывы:

Нет отзывов