Magtrol 6400 Скачать руководство пользователя страница 26

Страница: 26 / 56

Magtrol Model 6400 Torque Transducer Display

Chapter 4 – Manually Controlled Operation

OPERA

TION

3. Use UP

, DOWN

, LEFT

and RIGHT

buttons to select value.

4. Press and release SHIFT to exit and return to main menu.

4.1.5

ASS

AIL

ARAMETER

ETUP

Allows the user to set displayed pass/fail indication of torque, speed or auxiliary input.

1. Press and release SHIFT.

2. Press and release SETUP. "MENU: SYSTEM" appears in the display.

3. Press and release UP

button. "MENU: PASS/FAIL" appears in the display.

4. Press and release SHIFT. The display appears as follows:

POWER/AUX

TORQUE

SPEED

Figure 4–9 Torque Pass/Fail Setup Menu

5. Use UP

and DOWN

buttons to turn torque pass/fail testing ON or OFF.

6. If ON was selected, press and release SHIFT. The display appears as follows:

POWER/AUX

TORQUE

SPEED

Figure 4–10 High Limit Setup Display

If OFF was selected, go to step 10.

7. Use UP

, DOWN

, LEFT

and RIGHT

buttons to select the high limit for torque.

Select from a range of 0.0001 to 99999 displayed units.

8. Press and release SHIFT. The display appears as follows:

POWER/AUX

TORQUE

SPEED

Figure 4–11 Low Limit Setup Display

9. Use UP

, DOWN

, LEFT

and RIGHT

buttons to select the low limit for torque.

Select from a range of 0.0001 to 99999 displayed units.

Содержание 6400

























































Результаты поиска

Содержание 6400

Отзывы:

Magtrol 6400, Руководство пользователя, Страница: 26 / 56

Результаты поиска

Содержание 6400

Отзывы: