Magnetrol Echotel 962 Скачать руководство пользователя | Manualshive

Страница: 6 / 24

background image

6

51-650 Model 961/962 Echotel SIL Safety Manual

5.2

Skill Level of Personnel

Personnel following the procedures of this safety manual
should have technical expertise equal to or greater than that
of a qualified instrument technician.

5.3

Necessary Tools

No special equipment or tools are required to install Echotel
Model 961/962 ultrasonic level switch. The following items
are recommended:

• Wrenches, flange gaskets, and flange bolting appropriate for

process connection(s)

• Screwdrivers and assorted tools for making conduit and

electrical connections

• Digital multimeter or DVM for troubleshooting

5.4

Installation

The Model 961 single point switch may be used for high or
low level alarm, overfill protection, or seal pot level and
pump protection. Model 961 can be mounted vertically or
horizontally in vessels, bridles, or pipes.

The Model 962 dual point switch may be used to measure
high/low, high/high, or low/low levels. It can be used as a
level controller or to control pumps in an auto-fill or auto-
empty mode. Model 962 must be top mounted.

Refer Figures 2 –5 to the

Echotel Model 961/962 Ultrasonic

Switches Installation and Operating Manual

(Bulletin

51.646) for the proper installation instructions.

Bottom View

Figure 4

Horizontal Mounting

Bottom View

Figure 5

Nozzle Mounting

Use wrench on flats

Process

connection

Figure 3

Vertical Mounting

Pump

Protection

Fill Line

Dual Point Alarm

High Alarm

Low Alarm

Figure 2

Typical Mounting Orientations

«
...
4
5
6
7
8
...
»

Содержание Echotel 962

























Отзывы:

Нет отзывов

Похожие инструкции для Echotel 962

Бренд: Valor Страницы: 13

Бренд: Campbell Страницы: 31

Бренд: +GF+ Страницы: 8

Бренд: AEMC Страницы: 4

Бренд: Solinst Страницы: 2

Бренд: JUMO Страницы: 150

Бренд: Magtrol Страницы: 76

Бренд: Flexim Страницы: 160

Бренд: Neriox Страницы: 10

Бренд: UNI-T Страницы: 2

RLACS277RLACS29

Бренд: Racelogic Страницы: 10

Бренд: A&D Страницы: 2

Бренд: Rinstrum Страницы: 2

Бренд: Lambda Страницы: 35

Fusion-L 6 digit

Бренд: London Electronics Страницы: 44

Бренд: Ratek Страницы: 24

Бренд: Amptec Research Страницы: 19

Бренд: Feasa Страницы: 145

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды