Magnetrol Echotel 962 Скачать руководство пользователя | Manualshive

Страница: 1 / 24

background image

Ultrasonic

Level Switches

SIL Safety Manual for
Echotel

®

Model 961/962

Application

Echotel

®

Model 961/962 ultrasonic level switches utilize

pulsed signal technology to detect high, low, or dual-
point level in a broad range of liquid media applications.
The advanced self-test technology provides reliability
and continuous testing of electronics, transducer, piezo-
electric crystals, and electromagnetic noise.

Benefits

The Echotel Model 961/962 ultrasonic level switches
provide the following benefits:

• Single- or dual-point liquid level measurement

• Adjustable time-delay for turbulent aerated liquids

• Reliable liquid level measurement independent of

changes in media density, conductivity, or temperature

• Two-wire mA current shift and relay output options

• Relay output or mA current shift with separate

malfunction indication

• Integral or remote mount electronics

• Pulsed signal technology

• Extensive FM, CSA, ATEX and IEC explosion proof

and intrinsically safe approvals

• Suitable for Safety Integrity Level (SIL) 2 loops

Functional Safety Manual

This manual complements and is intended to be used with
the Magnetrol

Echotel

®

Model 961/962 Ultrasonic Single and

Dual Point Level Switches Installation and Operating Manual

(Bulletin 51-646).

Model 961

Model 962

1
2
3
...
»

Содержание Echotel 962

























Отзывы:

Нет отзывов

Похожие инструкции для Echotel 962

Бренд: NCTE Страницы: 10

Бренд: QUBINO Страницы: 2

Бренд: LaserLiner Страницы: 52

Бренд: Veris Страницы: 8

Бренд: Palstar Страницы: 15

Бренд: Oldham Страницы: 96

Бренд: ESP Страницы: 12

Smart Air Quality Monitor

Бренд: Lennox Страницы: 28

Бренд: Roland Страницы: 96

Бренд: PCE Health and Fitness Страницы: 11

XL4 SECOND STAGE

Бренд: Apeks Страницы: 21

Бренд: Jaquet Страницы: 27

Бренд: Kirby Morgan Страницы: 101

Бренд: BASI Страницы: 69

PHYSICS line C.A 832

Бренд: Chauvin Arnoux Страницы: 43

Photo Set Strato S-20

Бренд: Fisso Страницы: 2

VBOX Touch Motorsport V1

Бренд: Racelogic Страницы: 15

Бренд: PRESIDIUM Страницы: 86

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды