Magnetic mTripod Скачать руководство пользователя

Страница: 70 / 92

Control unit MGC mTripod

Corrective action

8.2

Malfunctions pedestrian gate

Malfunction: Display is difficult or impossible to read.

Possible cause

Corrective action

Removal by

Display contact set too light or

dark.

Correct display contact.

Page

41, chapter 5.6.

Technician

Malfunction: Pedestrian gate does not open.

Possible cause

Corrective action

Removal by

Power supply is not connected.

›

Switch on power supply.

›

Check power supply.

Technician

Error present. The

corresponding error message is

displayed.

Depending on error message,

check components, wiring, etc.

MHTM™ FlowMotion®

service expert

Power supply is present.

Control unit display does not

light up.

Control unit defective. Replace

the control unit.

MHTM™ FlowMotion®

service expert

Locking signal present.

›

Remove locking signal.

›

Check input function "Inhibit

opening".

Page 11.

MHTM™ FlowMotion®

service expert

8.3

Event, warning and error messages – definitions

The control unit differentiates between events, warnings and errors.
A message consists of a number, the category and a message text.

Event messages "INFO"

Event messages inform about events. The pedestrian gate continues to operate

normally. Event messages do not influence the outputs of the control unit.

Warning messages "WARNING"

Faults that could be reset by the control unit are displayed as warnings.

Operation of the pedestrian gate is not or only briefly impaired.

Error messages "ERROR"

Faults that cannot be reset by the control unit are displayed as errors. The

pedestrian gate is put out of service.

Содержание mTripod





























































































Результаты поиска

Содержание mTripod

Отзывы:

Похожие инструкции для mTripod

Бренды по названию

Популярные бренды

Magnetic mTripod, Руководство пользователя

Результаты поиска

Содержание mTripod

Отзывы:

Похожие инструкции для mTripod

Бренды по названию

Популярные бренды