manualshive.com logo in svg

Magnetic mTripod, Руководство пользователя

Магнитный мТрипод - компактный и удобный тренога для смартфонов с магнитным креплением. Легко устанавливается и удобно переносится. Бесплатно загрузите инструкцию по эксплуатации на manualshive.com, чтобы максимально эффективно использовать этот продукт.

Поделиться
Скачать
background image

49

Control unit MGC mTripod

Description of menus and parameters

6.2.6 

Signalling

Operational view > Main menu > Settings > Signalling

Parameter

Description

Buzzer/Siren

Activate events for which an acoustic signal is to be triggered. Connect the 

acoustic signal to the "Buzzer/Siren (alarm)" output.
An acoustic signal is possible for the following events:

 ›

Vandalism

 ›

Validation

 ›

Error

 ›

Random hit

 ›

Passage

 ›

Climbing/Crawling

Options

 ›

[   ]: Deactivated

 ›

[ X ]: Activated

Factory setting

 ›

Vandalism [ X ]

Signal move

Activate and deactivate the "Signal move" function.
If the function has been activated and a validation is available, the validation 

is signalled by a short rotation movement of the blocking element in the 

passage direction. Permanent opens are not signalled.
If signalling and validation are active, vend count for the opposite direction is 

deactivated. Pulses in the same direction are accepted.

Options

 ›

[   ]: Deactivated

 ›

[ X ]: Activated

Factory setting

 ›

[   ]: Deactivated

Содержание mTripod





























































































Отзывы:

Нет отзывов

Похожие инструкции для mTripod

Бренды по названию

Популярные бренды

Загрузить еще бренды