IMPULSE•G+/VG+ Series 4 Technical Manual
November 2022
Page 101
* Initial value is determined by X-Press Programming (
,
).
**
C08-19
Brk Slip Reset
Determines if BE6 alarm is automatically reset. If enabled,
VFD will always perform BE6 test after Load Float to
determine if brake is operational and the fault can be cleared.
If disabled the VFD will remain in BE6 alarm state until power
is cycled.
0, 1
0
0 Disabled
1 Enabled
C08-20
BE6 Check Torque Torque output during a BE6 check.
0.5–20.0%
1.0
C08-21
Add Mag I Time
Additional delay time at start to allow the motor to develop
additional magnetizing current.
0.0–3.0 sec
0.0
C08-22
Brk Slip Detect
Continuous monitoring for a slipping brake. (BE8 Detection)
0, 1
0
0 Disabled
1 Enabled
C08-23
Brk Slip Det Spd
Adjusts the sensitivity of BE8 Slip Detection.
0–10 Hz
1.0
C08-24
Brake Test Torq
Motor runs in Forward direction at C08-25 speed when MFDI =
61 is active. Brake output relay is not energized, PGO and
DEV detection are disabled. Monitor Brake Test Torque at
U01-86.
0–6553.5 Flb
(see **
below)
C08-25
Brake Test Speed
Speed to push at the brake during a Brake Test.
0–10 Hz
6
C08-27
Zero Spd Brk
Determines if the brake will set when passing through zero
speed.
0, 2, 3
0
0 Use Brake
2
Coast to Stop
3 Fast SFS Hold
C08-28
Trq Check Time
Time during which the torque must be above C08-03 or C08-
16 before releasing the brake. Increasing this time allows the
load to stabilize and minimize erroneous BE2 faults. Disabled
if set to 0.00.
0.00–2.55 sec
0.05
C08-29
Min REV Time
Maximum amount of time, after the brake has been released,
the VFD will remain running at in the down direction.
0.0–25.5 sec
1.2
C08-30
Pos Trq Time
Time that the internal torque signal must be positive before the
VFD will be allowed to transition from reverse to forward. Only
in effect within the C08-29 time, after brake release.
0.0–25.5 sec
0.4
C08-31
Pos Trq Speed
Speed, in the reverse/down direction, that the VFD will output
while waiting for the torque reference to go positive.
0.0–10.0 Hz
6.0
C08-32
Min Brk Set Time
Minimum time that the brake needs to be set, during BE5
detection, before a new run is allowed.
0.0-25.5 sec
0.1
C08-33
Dual Brake Test
Enabling this alternates the brake outputs after every run.
MFDOs must be set to 00 and 0A or OPE28 will be displayed
0, 1
0
0 Disabled
1 Enabled
C08-34
DIR Flt Trq Lvl
Regen torque level required to trigger a DIR fault. This is used
to detect an NLB hoist set up backwards (FWD is down).
Disabled if set to 0.
0–100%
20
Parameter
Display
Function
Range
Default
1.25x E02-11x5252
Motor RPM
Содержание Impulse G+ series 4
