Magnescale MG80-SC1 Скачать руководство пользователя страница 43

Страница: 43 / 51

8.3

Setup Commands

Write/Read

Description

SETUP

Command format

Start parameter setup.

SETUP

Starts parameter setup.

RSL= / RSL=

Command/Return format

Input resolution

①②

RSL=

③

= 1: 0.1μm

2: 0.5μm

3: 1μm

4: 5μm

5: 10μm

POL= / POL=?

Command/Return format

Input polarity

①②

POL=

③

= 0: Push-in direction is positive (+)

1: Push-in direction is negative (-)

MODE= / MODE=?

Command/Return format

Measured value mode

①②

MODE=

③

= 0: Current value (REAL) mode

1: Maximum value (MAX) mode

2: Minimum value (MIN) mode

3: Peak-to-peak value (P-P) mode

P= / P=?

Command/Return format

Preset value

①②

③

= The value differs depending on the measurement unit and input resolution.

Resolution mm unit

mm/25.4 unit

0.1μm

0.5μm

-99.9999 to 99.9999

-99.9995 to 99.9995

-9.99999 to 9.99999

-9.99998 to 9.99998

1μm

5μm

-999.999 to 999.999

-999.995 to 999.995

-99.9999 to 99.9999

-99.9998 to 99.9998

10μm

-9999.99 to 9999.99

-999.999 to 999.999

CH= / CH=?

CL= / CL=?

Command/Return format

Comparator upper limit

Comparator lower limit

①②

③

④

①②

③

④

③

= Comparator group number

④

= The value differs depending on the measurement unit and input resolution.

Note When changing the setting values, be certain after changes have been

made that the upper limit value is greater than or equal to the lower limit value.

Содержание MG80-SC1




















































Результаты поиска

Содержание MG80-SC1

Отзывы:

Magnescale MG80-SC1, Руководство по эксплуатации, Страница: 43 / 51

Результаты поиска

Содержание MG80-SC1

Отзывы: