Magnescale MG80-SC1 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 51

Magnescale MG80-SC1 Скачать руководство пользователя страница 16

15

/

48

5

Specifications

Model name

MG80-SC

Supply voltage

DC 10.8 to 26.4 V

Power consumption

2.4 W or less (not including the MG80-CM)

Maximum number of

connectable modules

MG80-CM: 16 modules

*1

Power input socket

Terminal block×1 (3-pin)

Interface connector

RS-232C 8P×1

RJ45×1 (shielding compatible)

Communication protocol

RS-232C (2,400 bit/s to 230,400 bit/s)

Ethernet (100BASE-TX: 100 Mbit/s)

Maximum cable length

RS-232C: 15 m

*2

Ethernet: 20 m (CAT5e shielded type recommended

*3

)

Module number setting

By rotary switch

Indicator lamps

Power: Green LED×1

Alarm: Red LED×1

Hold: Orange LED×1

Operating

temperature/humidity range

0 to +50°C (no condensation)

Storage temperature/humidity

range

–20 to +60°C (20 to 90% RH)

Mass

Approx. 130 g

Mounting method

DIN rail

*1 Up to 16 MG80-CM can be connected to each MG80-SC.

*2 Use a DZ252 or DZ254 RS-232C communication cable (sold separately).

*3 The customer must provide the Ethernet communication cables.

«
...
14
15
16
17
18
...
»

Содержание MG80-SC1




















































Отзывы:

Нет отзывов