Magenta 43 страница 3 Скачать руководство пользователя

Страница: 3 / 43

PROBLEM

CAUSE

REMEDY

REFERENCE

1. Skipping

1. Needle is not inserted

Insert the needle properly.

stitches

properly.

2. Needle is bent or worn.

Change the needle.

3. Incorrectly threaded.

Rethread.

4. Needle or thread are

Use the recommended sewing

inappropriate for fabric being

needle and thread.

sewn.

5. Sewing on stretch fabric.

Use A #11 blue tip needle.

6. Inappropriate needle bar

See mechanical adjustment

P. 15

height.

“

Needle bar height.”

7. Inappropriate needle to hook

See mechanical adjustment

P. 16

timing.

“Needle timing to shuttle.”

8. Inappropriate needle to

See mechanical adjustment

P. 12, 13

shuttle race clearance.

“Clearance between needle and

shuttle

race.”

2. Fabric not

1. Incorrect feed dog height.

See mechanical adjustment

P. 14

moving

“Feed dog height.”

2. Thread on bottom side of

Make sure to bring both needle

fabric is jammed up.

and bobbin thread under the foot

when starting sewing.

3. Feed dog teeth are worn.

Change the feed dog.

TROUBLESHOOTING

Содержание 43












































Результаты поиска

Содержание 43

Отзывы:

Похожие инструкции для 43

Бренды по названию

Популярные бренды

Magenta 43, Инструкция по эксплуатации, обслуживанию и список запчастей

Результаты поиска

Содержание 43

Отзывы:

Похожие инструкции для 43

Бренды по названию

Популярные бренды