Magenta 43 страница 23 Скачать руководство пользователя | Manualshive

Страница: 23 / 43

background image

21

MECHANICAL ADJUSTMENT

MOTOR BELT TENSION

TO CHECK:

1. If the motor belt tension is too tight or too loose, it can cause a belt noise: If the tension is too tight, it can cause
  the machine to run slowly and the motor to overload; if the tension is too loose; it can cause the belt to jump.
2. The correct motor belt tension is when the deflection of motor belt is about 7 to 9 mm.
  (when pushing the motor belt by finger with a 300 grams-force load.)

ADJUSTMENT PROCEDURE:

1. Remove the rear cover (see page 6).
2. Loosen the setscrews.
3. Move the motor up or down to adjust the deflection about 7 to 9 mm.
4. Tighten the setscrews.

300 gf load

Deflection 7 to 9 mm

Setscrew

Setscrew

«
...
21
22
23
24
25
...
»

Содержание 43












































Отзывы:

Нет отзывов

Похожие инструкции для 43

Бренд: Janome Страницы: 30

Бренд: Fastbind Страницы: 21

Бренд: Savin Страницы: 143

Бренд: easymaxx Страницы: 2

OFX 500 LINKFAX

Бренд: Olivetti Страницы: 230

Бренд: ICP DAS USA Страницы: 109

Бренд: Pacific Страницы: 8

Бренд: Singer Страницы: 12

SQF-200 SquareFolder

Бренд: Plockmatic Страницы: 85

Бренд: Dürkopp Adler Страницы: 80

Бренд: Duerkopp Adler Страницы: 77

Бренд: JUKI Страницы: 48

Бренд: JUKI Страницы: 92

Бренд: Singer Страницы: 34

Бренд: Life Fitness Страницы: 3

Бренд: Rexel Страницы: 20

Бренд: VETRON Страницы: 66

Answering Machine

Бренд: AT&T Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды