background image

WASP Line Array User Manual rev 2.00

6

 

                                           in

fo@mag-audio

.c

om

Tel./F

ax:

 +

38 044 277

-4

7-89

 

www

.mag-audio.com

2. Regulatory information

FCC COMPLIANCE NOTICE

This device complies with part 15 of the FCC 

rules. Operation is subject to the following two 

conditions: (1) This device may not cause harmful 

interference, and (2) this device must accept any 

interference received, including interference that 

may cause undesired operation.

CAUTION: Changes or modifications not expressly 

approved by the party responsible for compliance 

could void the user’s authority to operate the 

equipment.

NOTE: This equipment has been tested and found 

to comply with the limits for a Class B digital device, 

pursuant to part 15 of the FCC Rules. These limits are 

designed to provide reasonable protection against 

harmful interference in a residential installation. This 

equipment generates, uses, and can radiate radio 

frequency energy and, if not installed and used in 

accordance with the instruction manual, may cause 

harmful interference to radio communications. 

However, there is no guarantee that interference 

will not occur in a particular installation. If this 

equipment does cause harmful interference to radio 

or television reception, which can be determined 

by turning the equipment off and on, the user is 

encouraged to try to correct the interference by 

one or more of the following measures: 

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment 

and receiver.

- Connect the equipment into an outlet on a 

circuit different from that to which the receiver is 

connected.

- Consult the dealer or an experienced radio/TV 

technician for help.

EC DECLARATION OF CONFORMITY

Manufacturer: 

MAG Audio LLC 

Merezhna 2 

Bila Tserkva, Kyiv region 

09112 Ukraine

We declare under our sole responsibility that 

products:

WASP, WASP-S12, WASP-S18

Intended use: Professional Speaker System

Are in conformity with the provisions of the 

following EC Directives, including all amendments, 

and with national legislation implementing these 

directives:

- 2006/95/EC Low Voltage Directive 

- 2004/108/EC Electromagnetic Compatibility Directive 
- 2002/95/CE RoHs Directive

The following harmonized standards are applied:

EN 55103-1:2009 /A1:2012 

EN 55014-1:2006 /A1:2009 /A2:2011 

EN 55022:2010 /AC:2011 

EN 61000-3-2:2006 /A1:2009 /A2: 2009 

EN 61000-3-3:2013 

EN 61000-3-11:2000 

EN 61000-3-12:2011 

EN 55103-2:2009 /IS:2012 

EN 61000-4-2:2009 

EN 61000-4-3:2006 /A1:2008 /IS1:2009 /A2:2010 

EN 61000-4-4:2012 

EN 61000-4-5:2006 

EN 61000-4-6:2014 

EN 61000-4-11:2004 

EN 60065:2002 /A1:2006 /A11:2008 /A2:2010 /A12:2011

Bila Tserkva, 

22 January 2019

Alexey Asanov 

CEO

For compliance questions: [email protected]

Models:

Содержание WASP





















Отзывы: