Arm at this side
Arm at this side
BR600T Series
MAG Intelligent Vehicle Barrier Gate
User Manual v.1 2015
1) Warranty Coverage
2) Warning
a) In case of emergency, isolate power from the power supply.
b) Operate your barrier from suitable AC220 volts.
c) Improper installation can create danger (such as electric shock or fire). Please engage
specialist for the proper installation work.
d) Do not install Barrier Gate in a potentially explosive atmosphere.
e) If abnormal condition (burnt smell , etc...) occurs, switch off the power supply immediately.
!
3) Production Type
4) Technical Specification
6) Base Installation
7) Arm Installation
5) Product Elements
5.1) Barrier Parts
6.1) Mount the barrier base on the ground with screws. Refer to diagram below :
33 cm
30
c
m
Barrier Base
Plug Bolt
U-Channel Bracket
Plug Bolt Nuts
Plug Bolt
Barrier Base
U-Channel Bracket
Barrier
Body Housing
6.2) Do marking on the ground base on plug bolt distance (refer to diagram 6.2)
6.3) Screw U-Channel Bracket on the ground (refer to diagram 6.3)
M
ou
n
ting
fo
otp
ri
n
t
on the g
round
Diagram 6.1
Diagram 6.2
Diagram 6.3
Diagram 5.1
a) Mount the arm at the arm tray by screw. Refer to diagram 7.1
Diagram 7.1
8) Manual release arm by releasing clutch.
Arm can be move manually after unlocking the clutch.
This is useful during power failure where user can
manually lift the arm allowing traffic to pass through.
8.1) During power failure :
Step 1 : Turn key anti-clockwise to unlock the clutch
Step 2 : Lift arm vertical 90 degree
Step 3 : Turn key clockwise to lock the clutch
8.2) After power resume :
While arm still lift up
Step 1 : Press push button “UP” button one time
Step 2 : Press push button “DOWN” button.
Barrier arm will resume back to normal operation.
9) Counter - Weight spring adjustment
9.1) Selection of the spring
Arm Tray
Barrier Arm
Mount the arm
at the arm tray
Plastic Clip
MAG warrants each new product manufactured and sold by it or one of its authorized
distributors only againts defects in workmanship and/or materials under normal service,
proper installation and use. THIS WARRANTY IS LIMITED TO REPAIR OR REPLACEMENT OF
VERIFIED DEFECTIVE PRODUCTS AND EXCLUDES ANY AND ALL RISK AND LIABILITY
WHATSOEVER RESULTING FROM ANY USE OF SAID PRODUCTS, INCLUDING INCIDENTAL AND
CONSEQUENTIAL DAMAGES. THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE
DESCRIPTION ON THE FACE THEREOF. The provisions of this warranty and limitation of liability
shall not modified in any respect except by written document signed by MAG.
9.2) Calibrating counter-weight spring tension
Tension of counter weight spring needs to be calibrated according to arm length and weight
to achieve minimum burden on the motor. This will ensure maximum life time on the motor.
Step 1 :
Turn the key clockwise to unlock the clutch. Refer diagram 9.2a
Feature
Model No.
Open/close
speed
Max straight
arm
Arm swing
out
BR630T
3 sec
4 meter
Yes
BR660T
6 sec
6 meter
No
BR630T_90
3 sec
4 meter
No
BR660T_FE
6 sec
4.5 meter
No
Description
Parameter
Mechanical temperature
-40° to 75 C
Electrical temperature
-10° to 75 C
Power supply input
220V ± 10% AC, 50/60Hz
Power consumption
80 watt
Relative humidity
< 90 %
Arm speed
d
n
o
c
e
s
6
,
3
,
8
.
1
Internal lubrication
Grease
Max starting torque
1.8 second :
1.4±0.2 N .M
3 / 6 second :
0.87±0.1 N.M
AC rotation speed
1.8 second :
440±40 R PM
3 / 6 second :
900±50 R PM
BR618T
1.8 sec
4 meter
Yes
Top Cover
Arm
Body Housing
U-channel bracket and plug bolt
for installing barrier gate
Top cover can remove
from the body house
Key opening to
unlock clutch
Key (to lock &
unlock the clutch)
Housing Door
Housing door
can remove
from body
housing
UnLock
Lock
UnLock
Model
Features
Red Spring
(4.5mm )
Green Spring
(4.0mm )
Blue Spring
(5.5mm )
BR618T
BR630T
BR660T
BR630T_90
BR660T_FE
2
1
1
1
1
1
1
1
1
b) Assemble telescopic arm. Refer to diagram 7.2
Step 1:
Find 2 nos screw
from arm cover
Step 2:
Secondary arm must be fully
pulled out. Mount 2 screws
tightly at the middle section to
secure the join between
primary and secondary arm.
Arm will shake if screw is not
mounted tightly. Secondary
arm can be cut shorter to
adjust to lane.
Door at this side
Arm at this side
13cm
19.5cm
diagram 9.2a
Diagram 7.2
5.2) Motor Parts
Diagram 5.2
Spring Pin
Balance Spring
Spring Base
Motor Sensor
Motor
Drive Crank
Arm Tray
Screw Threadpole
Initiative Crank
Balance Crank
Ir sensor limit
Brace pole
Rubber cushion
Door at this side
Door at this side
GROUND
GROUND
Housing position can be still be adjusted
before completely securing the nuts.
