MAG TOOLS MB190UC Скачать руководство пользователя страница 1

MB190UC-BL / MB190UC-BK / MB190UC-OR / MB190UC-GR / MB190UC-NG / MB190UC-YE 

Rev. 03/16/05

Due to the weight of this cart we recommend that  

TWO PEOPLE

 work together on the assembly. This cart weighs 

approximately 200lbs, please use caution during assembly.  

Step 1:

  Locate the key tied to the bottom shelf. Using the 

key, open the sliding top and remove the caster box 

from the bottom drawer. Once removed make sure all 

drawers are completely closed and the inside lever is 

in the locked position. Close the sliding top and lock.  

Step 2:

  Lay out a work surface using the protective foam  

provided. Once this surface is secure gently turn the 

cart onto its back. (You may choose to lay it on its top 

instead)

Step 3:

  (Before assembling the legs remove the cable tie 

holding the bumper in place) Insert the front leg 

(Part #7), labeled FL or FR. Then place the front 

bumper (Part # 13) over the leg aligning the center 

bolt holes. With holes aligned insert stove bolt (Part 

#1a) and finger tighten with nyloc nut and washer.

Step 4:

  Install back leg (Part #7) labeled BL or BR and bumper 

(Part #13) following the same procedure as above. 

Step 5:

  Repeat steps 3 & 4 to mount the legs on the  

opposite side.  

Step 6:

  Completely tighten the 8 bolts just inserted.

ASSEMBLY INSTRUCTIONS

Step 7:

  Insert bottom shelf (Part # 18) between the four legs 

flat side facing up towards the ceiling. Insert sixteen 

stove bolts (Part #1a) and completely tighten.

18

1a

1a

MB190UC, -BK, -BL, -GR, -NG, -OR, -YE  

3 Drawer Deluxe Utility Cart

1a

13

7

1a

13

7

MB190UC_Manual_031505.indd   1

3/16/05   2:11:41 PM

Содержание MB190UC

Страница 1: ...e to lay it on its top instead Step 3 Before assembling the legs remove the cable tie holding the bumper in place Insert the front leg Part 7 labeled FL or FR Then place the front bumper Part 13 over the leg aligning the center bolt holes With holes aligned insert stove bolt Part 1a and finger tighten with nyloc nut and washer Step 4 Install back leg Part 7 labeled BL or BR and bumper Part 13 foll...

Страница 2: ...ers Put the four casters in place The two locking casters Part 10 should be on one side of the cart and the two non locking casters Part 9 should be on the other Left or right side NOT front or back Using the 16 bolts Part 8 washers and fasteners located in separate Caster bag completely tighten the casters to the bottom tray using a 13mm socket and 14mm combination wrench for the bolt head Note B...

Страница 3: ...ge the drawer Solution The inside Lock Unlock slide potentially could fall out of its groove while turning the cart on its lid back or onto its casters Unscrew the four screws that are holding the Lock Unlock slide in place Once the screws are removed simply place the latch back onto the slide and tighten the four screws back down HARDWARE SPECIFICATIONS 1a x 32 pcs 1b x 8 pcs 2 x 72 pcs 3 x 56 pc...

Страница 4: ...ter with lock each 11 RSBKT 2 Bracket for paper storage area 12 RS190UCDHBK Black Drawer Handle each 13 RS190UCBP 1 Set of 4 Bumpers 14 RSLK Lock with Keys 15 RSSCD R Red Spray Can Divider RSSCD BK Black Spray Can Divider RSSCD BL Blue Spray Can Divider RSSCD GR Green Spray Can Divider RSSCD NG Neon Green Spray Can Divider RSSCD OR Orange Spray Can Divider RSSCD Y Yellow Spray Can Divider 16 MBD19...

Отзывы: