madur electronics maMoS 100 Скачать руководство пользователя страница 41

Страница: 41 / 96

www.madur.com

Manual

maMoS

100/200/300/400

12. In the next window change

DHCP

option from

“0 – Disabled”

“1 – Enabled”

and confirmed it by pressing

“OK”

button.

Picture 45.

Setting the DHCP option.

13. After returning to the previous window press

“Refresh”

button and reselect

the device from the list.

14. Leave the rest of the options as default by pressing the

“Next”

button in the

following windows in the

Wizard Configuration

15. After completing the

Wizard Configuration

go to

MaMoSII.exe

program

(see chapter 7.3.2. ) and select the configured COM port.

5.4. MMC module.

The

maMoS

monitors can be optionally equipped with a module used for regis-

tering the measurements results on a flash memory card (

MultiMedia Card

) in a digital

way. If the module is installed the card slot can be found underneath the lowest display.

Such a module is shown in Picture 46. On the right-hand side of the card slot (1) there is a

button (2) used for holding the recording process (if the card is to be removed) and a con-

trol LED (3) which signalises the current work mode of the MMC.

Содержание maMoS 100

































































































Результаты поиска

Содержание maMoS 100

Отзывы:

madur electronics maMoS 100, Руководство пользователя, Страница: 41 / 96

Результаты поиска

Содержание maMoS 100

Отзывы: