madur electronics maMoS 100 Скачать руководство пользователя страница 32

Страница: 32 / 96

www.madur.com

Manual

maMoS

100/200/300/400

monitor is on. Moving the control from monitor to computer is a great improvement espe-

cially if the monitor has been installed in a hard to reach place.

5.3.1. Monitor network (RS485)

Up to 15 monitors equipped with the RS485 communication interface can form a

network and be controlled by a single computer with the use of a single session of the

MaMoSII.exe

program. This useful possibility will simplify the simultaneous operating

monitors located in different places.

To form such a network all the devices should be connected to the computer via

an appropriate switch unit. Such a device -

RS485 Switch

is on offer in the

catalogue. The switch (Picture 30.) has nine connectors designed for

connecting the monitors and one used for connecting the computer.

Picture 30.

Switch for connecting the monitors into the RS485 network.

Each of the monitors should be connected to the inputs labelled

"Analyser #1"

"Analyser

#9"

, whereas the computer should be connected to the

"Computer"

connector. The net-

work can be formed by up to 15

maMoS

monitors.

Содержание maMoS 100

































































































Результаты поиска

Содержание maMoS 100

Отзывы:

madur electronics maMoS 100, Руководство пользователя, Страница: 32 / 96

Результаты поиска

Содержание maMoS 100

Отзывы: