madur electronics maMoS 100 Скачать руководство пользователя страница 18

Страница: 18 / 96

www.madur.com

Manual

maMoS

100/200/300/400

Picture 17.

Power supply connectors

ATTENTION!

Connecting the supply to the connectors other than shown in

the Picture 17. will cause the permanent damage to the device.

3.5. Configuration possibilities

Due to its modular design, the

maMoS

monitor can be configured in many differ-

ent ways. Below all the extra modules and the gases the monitor measures have been lis-

ted.

3.5.1. Types of the measured gases

The

maMoS

monitor can measure the concentration of up to four different gases

using electrochemical or

NDIR

(Non-dispersive Infrared) sensors. In the Table 1. the

sensors which can be used by the monitor have been listed.

Due to continual development of the monitor, the sensor types and their measure-

ment ranges might change. If the needed sensor or measurement range does not appear

Содержание maMoS 100

































































































Результаты поиска

Содержание maMoS 100

Отзывы:

madur electronics maMoS 100, Руководство пользователя, Страница: 18 / 96

Результаты поиска

Содержание maMoS 100

Отзывы: