madur electronics maMoS 100 Скачать руководство пользователя страница 16

Страница: 16 / 96

www.madur.com

Manual

maMoS

100/200/300/400

Picture 15.

The PWM output and the load connection.

One of the two connectors:

12V

VCC

(+5V) (Picture 15.) can be used for sup-

plying the receiver controlled via the output. If the 12V supply is used the maximum load

current amounts 500mA, whereas for the 5V supply it is 200mA.

3.3.4. Relay outputs (optional)

Optionally the monitor can be equipped with two independent

SPDT

relays

Re-

lay #1

and

Relay #2

connected with a connector as shown in Picture 16. The B ending is a

common ending, the A ending is a normally closed ending (

) and the C ending is a nor-

mally open ending (

). The

Relay #1

is connected with the

and

connectors,

whereas the

Relay #2

is connected with

and

. The relays enable the user to

switch voltages up to 230V and currents below 2A.

The relays can:

−

be controlled by one of the analogue outputs

(according to

the level of signal on the analogue output the relay either switches on or off

with a certain hysteresis).

−

be controlled by the digital input (the relay follows the

In1

In2

digital input

state, which means it switches on when the input is active and switches off

when it is inactive).

−

work according to the measurement cycle stage (the relay switches on in the

“

MEASUREMENT"

stage and switches off during other stages)

−

be permanently switched off.

Содержание maMoS 100

































































































Результаты поиска

Содержание maMoS 100

Отзывы:

madur electronics maMoS 100, Руководство пользователя, Страница: 16 / 96

Результаты поиска

Содержание maMoS 100

Отзывы: