madur electronics maMoS 100 Скачать руководство пользователя страница 15

Страница: 15 / 96

www.madur.com

Manual

maMoS

100/200/300/400

Picture 14.

Analogue outputs on the monitor.

The analogue output (

) signal range is 0 ÷ 5V or 0 ÷ 10V (set with the help

of the

MaMoSII.exe

software), whereas the current output (

) signal range is 0÷20mA

or 4÷20mA (also set with the help of the

MaMoSII.exe

software).

3.3.3. Digital output (PWM)

The monitor has a single digital

PWM

output (

PV3

). This is an open drain output,

the active state of the output means short-circuiting the

PV3

ending

to the ground potential

by internal high-power N-MOS transistor. This can be used for switching an external relay,

etc. The

PWM

output can be controlled via analogue outputs or digital inputs. It can also

proceed to the active state when the monitor has initiated the measurement phase. The

PWM

output function can be defined with the help of the

MaMoSII.exe

software.

Содержание maMoS 100

































































































Результаты поиска

Содержание maMoS 100

Отзывы:

madur electronics maMoS 100, Руководство пользователя, Страница: 15 / 96

Результаты поиска

Содержание maMoS 100

Отзывы: