manualshive.com logo in svg

Macurco BRS-485, Инструкция пользователя

Поделиться
Скачать
Macurco BRS-485 Скачать руководство пользователя страница 19

Macurco MRS-485 Modbus RS-485 Adapter 

 

REV – 1.0 

[34-2900-0019-7] 

18 

|

 

P a g e

 

 

4.3

 

Firmware and Configuration Update 

To receive the latest version of Macurco NPU, as well as firmware and configurations, download the Macurco 

NPU from our website http://www.macurco.com/downloads.html. If a newer version of firmware is available in 
the NPU you will be prompted to update when connected to the BRS-485. 

Macurco NPU Folder downloaded from website contains a file "BRS-485_VXXX.DUF" where VXX is the version 

number. This file is the configuration file for different communication protocol supported by BRS-485.  This 
configuration file can be uploaded to BRS-485 using following procedure. 

a. Open the Macurco Network Parameter Utility Software.  

b. If BRS-485 is connected to PC via USB, the software will display home screen like one in Figure 5-1. If Software 

does not detect the BRS-485 it will display “No Device Connected”. Make sure software detects the panel before 
proceeding.  

c. Go to File (on the top left corner of the software) and select “Update Device…”.  

d. A new window will pop up to select the file. Select the DUF file and hit Open.  

e. Now the DUF file will be loaded into the panel. The progress of the file update is displayed at the bottom.  

Figure 4-3 

f. Once the update is complete it will reset the device and it will return to home screen. Verify the correct 

version of the device configuration file is updated. Device configuration version is displayed alongside the 

product image displayed in NPU software. It has format "Multi-Protocol VX.XX" where X.XX corresponds to the 
device configuration version. 

Содержание BRS-485


































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды