Macurco BRS-485 Скачать руководство пользователя

Страница: 10 / 33

Macurco MRS-485 Modbus RS-485 Adapter

REV – 1.0

[34-2900-0019-7]

P a g e

Figure 3-1 BRS-485 Installation Expanded

The 6-Series detector mounts on a 4”x 4” electrical box supplied by the contractor.

Connect the detector to the control cables with terminal plugs. When making connections, make sure

the power is off.

There are two terminals for the dry alarm relay contacts, again with no polarity preference. The alarm

relay can switch up to 0.5 A 120 V, or 60 VA. The alarm relay is activated if gas reaches or exceeds the

alarm settings. See Operation of the detector User Instructions for details on relay settings.

The alarm relay can be configured to normally open (default) (N.O.) or normally closed (N.C.) and will

activate if the gas concentration exceeds alarm set point. It will deactivate once the gas concentration

drops below the alarm set point. Note that the “disable” setting will cause the alarm relay not to engage

at all.

The dry contact, SPDT fan relay has three terminals: The Common (COM), normally open (N.O.) and the

normally closed (N.C.) contact. The fan relay can switch up to 5.0 A up to 240 VAC. See Operation section

of the detector User Instructions for details on relay settings.

Содержание BRS-485


































Результаты поиска

Содержание BRS-485

Отзывы:

Похожие инструкции для BRS-485

Бренды по названию

Популярные бренды

Macurco BRS-485, Инструкция пользователя

Результаты поиска

Содержание BRS-485

Отзывы:

Похожие инструкции для BRS-485

Бренды по названию

Популярные бренды