background image

TECHNICAL SPECIFICATIONS

The KR Grease gun is suitable for use with Macnaught
models K3 and K6 Lubrication systems.

The KR Grease Gun is recommended for use with
greases up to and including NLGI No 2 consistancy.

The KR Grease Gun will deliver greasing pressures up
to 10,000 psi (69 MPa) on the high pressure setting.

The K6 Mini-Lube pump will deliver 30 shots of grease
on each prime of the pump.

8

             

   Macnaught Pty Ltd

PO Box 90 Arncliffe NSW 2205 Australia
           Telephone (02) 9567 0401
           Facsimile   (02) 9597 7773
      Email:  [email protected]
        Web: www.macnaught.com.au

Macnaught Pty Ltd (“Macnaught”) warrants that all Products manufactured by Macnaught and
purchased after 1

st

 of July 1999 will be free from any defects caused by faulty materials or

workmanship for a period of (5) years from the date of purchase of the product, provided that
during the Warranty period:
1)

Macnaught receives notice setting out full details of any defect in any product and
details of the time and place of purchase.

2)

The Purchaser, at their own cost returns the product to the nearest authorized  Macnaught
service center.

For componentry contained in the product, (such as o’rings, seals, springs and hoses )  which
are subject to wear, the warranty period will be (12) months from the date of purchase of the
product.

Macnaught shall, at its option repair or replace any product found defective by its inspection.
This warranty does not cover failure of parts or components which, in the judgment of Macnaught,
arises from misuse, abrasion corrosion, negligence, accident, substitution of non-Macnaught
parts, faulty installation or tampering.

If Macnaught inspection discloses no defect in material or workmanship, repair or replacement
and return will be made at customary charges.
Macnaught’s liability and the purchaser’s rights under this Warranty shall be limited to such
repair or replacement and in particular, shall not extend to any direct, special, indirect or
consequential damage or losses of any nature.
The foregoing warranty supersedes, voids and is in lieu of all or any other warranties.

“Note: This warranty does not form part of, nor does it constitute, a contract between Macnaught
and the end-user or purchaser. It is additional to any warranty given by the seller of the products.

This warranty does not exclude, limit, restrict or modify the non-excludable rights or remedies
conferred upon the end-user or purchaser, or the non-excludable duties or liabilities imposed
on the seller or Macnaught, by Part V, Divisions 2 and 2A of the Trade Practices act 1974
(Commonwealth) or other legislative provisions. Macnaught otherwise excludes, to the extent
permitted by law, any rights conferred on the end-user or duties or liabilities imposed upon it.”

 

                               

        

WARRANTY POLICY

Содержание MINI-LUBE K6









Отзывы: