macnaught.com
INSTRUCTION MANUAL
IMPORTANT INFORMATION
The information contained will help ensure
many years of dependable performance
and trouble free operation.
Please take a few moments to read through
this instruction manual before operating
your new L-OD90B waste oil drainer unit.
READ THIS INFORMATION
CAREFULLY BEFORE USE.
Please retain this instruction manual for future
reference.
Your safety is important to us. Please read and
follow all instructions listed below. Some of
these instructions alert you to the potential for
personal injury.
“Cautions” throughout the manual advise
of potential practices or procedures which may
cause damage to your equipment.
Make sure all operators have access to adequate
instructions about safe operating and
maintenance procedures.
DO NOT exceed the maximum oil temperature of
120C.
WARNING!
Before attempting any repairs or maintenance
of this product, disconnect the air supply to
release the air pressure.
Do not extract brake fluid, caustic or flammable
products.
DO NOT modify any component of this
equipment.
ASSEMBLY PROCEDURE
1. Connect the wheels to the axle, tighten the
screws. Insert the castors into the holes
provided and tighten securely.
2. Insert the handle to the handle location tubes
and tighten the screws securely.
3. Insert the gravity drain tube into the top hole
on the container and tighten.
4. Attach the oil collecting pan to the top of the
tube and tighten securely.
5. Insert the plastic strainer into the oil pan and
fit the oil pan extender.
6. Attach the tool holder onto the brackets
located on the top of the container.
OPERATION
WARNING!
Check the safety relief valve on the holding
tank weekly for correct operation. The Safety
valve should open at 1bar (14.5psi).
GRAVITY DRAIN USE
1. Open the ball valve located under the
gravity drain.
2. Close the discharge ball valve located at the
bottom of the holding tank.
3. Position the gravity bowl under the sump
plug. Remove sump plug and drain the waste
oil into the funnel.
AREA 4:
FOR BATTERY CAPACITY
AREA 2:
FOR MEASUREMENT UNITS
Value
ER14250 3.6V
1-35L/min
0.5-100bar
Data
Flow rate
Operating Pressure Range
60°C
±0.5%
Accuracy
Battery
Max operation temperature
1
2
3
4
5
6
Fig. 2
1. Air supply
2. Shut off air valve
3. Oil Pump
4. Shut off oil valve
5. Hose reel
6. Oil control valve
Display and button usage
Notes: It will flashing when
battery voltage less than 3.3V;
AREA 1:
FOR LAST DISPENSE CYCLE
AREA 3:
FOR ACCUMULATED TOTAL
Menu:
MOVING THE NUMBERS FOR
ADJUSTING THE CALIBRATION
AND CHOOSING THE UNITS
Reset:
CHOOSING THE UNITS AND
SETTING CORRECTION FACTOR
AREA 4:
FOR BATTERY CAPACITY
AREA 2:
FOR MEASUREMENT UNITS
Value
ER14250 3.6V
1-35L/min
0.5-100bar
Data
Flow rate
Operating Pressure Range
60°C
±0.5%
Accuracy
Battery
Max operation temperature
1
2
3
4
5
6
Fig. 2
1. Air supply
2. Shut off air valve
3. Oil Pump
4. Shut off oil valve
5. Hose reel
6. Oil control valve
Display and button usage
Notes: It will flashing when
battery voltage less than 3.3V;
AREA 1:
FOR LAST DISPENSE CYCLE
AREA 3:
FOR ACCUMULATED TOTAL
Menu:
MOVING THE NUMBERS FOR
ADJUSTING THE CALIBRATION
AND CHOOSING THE UNITS
Reset:
CHOOSING THE UNITS AND
SETTING CORRECTION FACTOR
AREA 4:
FOR BATTERY CAPACITY
AREA 2:
FOR MEASUREMENT UNITS
Value
ER14250 3.6V
1-35L/min
0.5-100bar
Data
Flow rate
Operating Pressure Range
60°C
±0.5%
Accuracy
Battery
Max operation temperature
1
2
3
4
5
6
Fig. 2
1. Air supply
2. Shut off air valve
3. Oil Pump
4. Shut off oil valve
5. Hose reel
6. Oil control valve
Display and button usage
Notes: It will flashing when
battery voltage less than 3.3V;
AREA 1:
FOR LAST DISPENSE CYCLE
AREA 3:
FOR ACCUMULATED TOTAL
Menu:
MOVING THE NUMBERS FOR
ADJUSTING THE CALIBRATION
AND CHOOSING THE UNITS
Reset:
CHOOSING THE UNITS AND
SETTING CORRECTION FACTOR
Gravity drain
pipes
Handle
Wheels
Sight
glass
MAC0619_Lubemate_InstructionManual_L-OD90B_D2.indd 3-4
7/8/18 4:47 pm
L-OD90B
2
.
Lubemate | Waste Oil Evacuation System