Mack M359 Скачать руководство пользователя

Страница: 80 / 332

SAFETY

SAFETY EQUIPMENT

Safety triangles and fire extinguishers

are available as optional equipment. The

Federal Motor Carrier Safety

Administration requires commercial

motor vehicles to be equipped with an

appropriate sized fire extinguisher and

safety warning devices. The equipment

can be ordered from and installed by

Mack Trucks or installed by the vehicle

owner.
The fire extinguisher must be located so

that it is readily accessible for use. The

extinguisher must be securely mounted

to prevent sliding, rolling, or vertical

movement relative to the motor vehicle.
The safety triangles must be securely

attached to any light-tight, enclosed,

and easily accessible compartment.
Please refer to Federal Motor Carrier

Safety Regulation 49CFR393.95,

Emergency Equipment and Federal

Motor Vehicle Safety Standard

49CFR571.125, Warning Devices for a

complete listing of the requirements.

Warning Triangles, Rear Wall

The warning triangles are stored in a

box, secured to the floorboard, located

against the rear wall of the cab.

X Publication_PC28

Содержание M359













































































































































































































































































































































Результаты поиска

Содержание M359

Отзывы:

Похожие инструкции для M359

Бренды по названию

Популярные бренды

Mack M359, Руководство пользователя

Результаты поиска

Содержание M359

Отзывы:

Похожие инструкции для M359

Бренды по названию

Популярные бренды