Mack M359 Скачать руководство пользователя страница 193

Страница: 193 / 332

STARTING AND DRIVING

VEHICLE SPEED RETARDING DEVICES

DANGER

When operating a tractor bobtail (without

a trailer) or on slippery roads, the engine

brake switch must be in the "OFF"

position. Failure to follow this instruction

can result in loss of vehicle control and

serious personal injury or death.

NOTE

The vehicle ABS will automatically turn off

the vehicle speed retarding device, IF one

of the sensed rear wheels is locking up as

a result of vehicle speed retarding device

operation. The vehicle speed retarding

device will be turned back on

automatically when the wheels become

unlocked. Consider switching to a lower

braking level if this occurs frequently.

NOTE

It is normal for there to be a slight delay in

the application of a vehicle speed

retarding device. When using devices of

this type, be sure to think ahead and

analyze conditions in order to use the

device properly.

A vehicle speed retarding device is not

intended to bring the vehicle to a stop. A

vehicle speed retarding device is only

intended to retard the vehicle speed

under certain conditions.

183

X Publication_PC28

Содержание M359













































































































































































































































































































































Результаты поиска

Содержание M359

Отзывы:

Похожие инструкции для M359

Бренды по названию

Популярные бренды

Mack M359, Руководство пользователя

Результаты поиска

Содержание M359

Отзывы:

Похожие инструкции для M359

Бренды по названию

Популярные бренды