Mack M359 Скачать руководство пользователя

Страница: 183 / 332

STARTING AND DRIVING

AXLES

Differential Locks

DANGER

DO NOT drive on dry, paved surface with

the differential lock engaged. The vehicle

strives to maintain a straight line. Taking a

curve with the differential lock engaged

can cause an accident, leading to serious

personal injury or death.

CAUTION

Never operate the vehicle with the

differentials locked any longer than is

necessary. This state places a great strain

on the axles and can cause rapid tire

wear.

Under normal traction conditions, do not

engage the differential lock. If possible,

do not use the differential lock while

taking a curve. With good traction and

the differential lock engaged, the vehicle

is under steered and therefore tends to

drive straight in a curve. When using the

lock on good traction surface, drive

cautiously and do not exceed 40 Km/h

(25 mph). Disengage the lock as soon as

possible.
When the differential lock is disengaged,

the couplings can be under tension.

Disengage the lock by returning the

switch to the OFF position. Help with the

disengagement by briefly letting up on

the accelerator to relieve the torque on

the couplings.
The drive axle can be equipped with the

differential lock. The single drive axle

only has a wheel differential lock. With

tandem drive axles; there could be both

interwheel differential lock and an

interaxle differential lock.
Use the differential lock on icy or

slippery surfaces. When the slippery

surface is passed, disengage the

differential lock. The differential lock

must not, under any circumstances, be

engaged when in a wheel-spin situation.

Engage the lock ahead of the slippery

area. If already slipping, stop the wheels,

engage the lock, and then continue.

Engaging the differential lock when the

wheels are spinning, damages the

differential and the rear axle drive unit

could possibly fail.
All efforts must be made to avoid

spinning the wheels at high speeds on

slippery surfaces. This fact is true

whether the differential lock is engaged

or not. Excessive wheel spin can result

in failure of the cluster gears, axle shafts

and other components found within the

rear axle housing. If unable to obtain

traction, engage the differential lock as

described. If still unable to move the

truck, seek assistance from a qualified

tow operator. Engaging the differential

locks must always be done as follows:

1 Press the service brakes. If

necessary, press the clutch pedal.

Wait for the drive wheels to stop

spinning.

2 Press the Differential Lock switch.
3 Select a suitable gear for the

transmission.

4 Release the service brakes. If

necessary, release the clutch pedal.

Interaxle Differential Lock Switch

173

X Publication_PC28

Содержание M359













































































































































































































































































































































Результаты поиска

Содержание M359

Отзывы:

Похожие инструкции для M359

Бренды по названию

Популярные бренды

Mack M359, Руководство пользователя

Результаты поиска

Содержание M359

Отзывы:

Похожие инструкции для M359

Бренды по названию

Популярные бренды