Mack M359 Скачать руководство пользователя страница 143

Страница: 143 / 332

DRIVING ENVIRONMENT

MISC CAB EQUIPMENT

Dome Light

Dome lights are located on the roof of

the truck and controlled by the switch

located in the overhead front

compartment. Each switch can be

manually controlled by the driver and

passenger or the driver can turn both on

together.

Fresh Air Vent

An air vent is provided to circulate

outside air to the cab. Move the vent

scroll wheel to the right to open the vent

and to the left to close the vent.
When heating the cab, all fresh air vents

should be closed. However, the vents on

the outer parts of the dash can be used

for defrosting the cab door windows.

When operating the air conditioning, all

air vents should be completely open and

the air flow directed upward.

Cab Air Filter

To provide comfortable and clean fresh

air in the cab, the heating and air

conditioning system is designed with a

replaceable filter. Under normal

operating conditions the filter should be

replaced every 6 months to ensure the

efficiency of the heating and air

conditioning system. Failure to replace

the filter may cause damage to

heater/AC components.

NOTE

Dusty conditions may require more

frequent replacement.

133

X Publication_PC28

Содержание M359













































































































































































































































































































































Результаты поиска

Содержание M359

Отзывы:

Похожие инструкции для M359

Бренды по названию

Популярные бренды

Mack M359, Руководство пользователя

Результаты поиска

Содержание M359

Отзывы:

Похожие инструкции для M359

Бренды по названию

Популярные бренды