Mack M359 Скачать руководство пользователя страница 140

Страница: 140 / 332

DRIVING ENVIRONMENT

SEATS

General Information

DANGER

All adjustments are to be made while the

operator is seated and the vehicle is

stationary. DO NOT adjust the seat

position while driving the vehicle. Failure

to follow this warning can result in loss of

vehicle control, which can result in serious

personal injury or death in the event of a

vehicle accident.

The vehicle seats keep the driver

positioned safely behind the wheel.

Depending on the configuration of the

vehicle, it may be equipped with one of

the following seats in this section.
The seats have many functions

designed to enhance driver comfort.

Mack recommends getting to know

these features well before operating the

vehicle.

Sears Premium Seat

Heat Switch

Seat Bolster Valve

Back Bolster Valve

Lumbar Valve

Suspension Valve

Damper Adjustment

3 Position Seat Tilt/Extension

Fore-Aft Slide Handle

10 Fore-Aft Isolator Handle
11 Recliner Handle

Sears Mid-Level Seat

Seat Bolster Valve

Back Bolster Valve

Lumbar Valve

Suspension Valve

3 Position Seat Tilt/Extension

Fore-Aft Slide Handle

Fore-Aft Isolator Handle

Recliner Handle

10 Swivel Handle

130

X Publication_PC28

Содержание M359













































































































































































































































































































































Результаты поиска

Содержание M359

Отзывы:

Похожие инструкции для M359

Бренды по названию

Популярные бренды

Mack M359, Руководство пользователя

Результаты поиска

Содержание M359

Отзывы:

Похожие инструкции для M359

Бренды по названию

Популярные бренды