Mack M359 Скачать руководство пользователя страница 120

Страница: 120 / 332

DRIVING ENVIRONMENT

CAB CLIMATE CONTROL

Cab Climate Control

Blower Control Knob

Temperature Control Knob

Mode Knob

Fresh/Recirculation Button

A/C ON/OFF Button

1 Blower Control Knob

This knob controls fan speed from

OFF to 4 (highest speed).

2 Temperature Control Knob

Controls the temperature of the air in

the cab from COOL (far left) to HOT

(far right).

3 Mode Selection Knob Controls the

direction of air flow around the cab

seen below.

4 Fresh/Recirculation Switch or Button

Selects the cab intake air between

fresh air (from outside the cab) and

recirculated air (inside the cab).

5 Air Conditioner ON/OFF Switch or

Button

Activates the air conditioning

system.

Directs airflow through the dash panel air

vents only.

Directs airflow through both the dash panel

and floor air vents (bi-level).

Directs airflow through the floor vents only.

Directs airflow through the floor vents and the

windshield for defrosting and/or defogging.

Directs airflow only to the windshield for

defrosting and/or defogging.

NOTE

The Mode Selection knob can be rotated

to any position. This allows the operator to

select the desired amount of blend

between the positions.

NOTE

For maximum air conditioner

performance, select recirculated air.

NOTE

Turn the bunk and dash blower fan to 0 or

OFF before initiating remote software

update operations.

110

X Publication_PC28

Содержание M359













































































































































































































































































































































Результаты поиска

Содержание M359

Отзывы:

Похожие инструкции для M359

Бренды по названию

Популярные бренды

Mack M359, Руководство пользователя

Результаты поиска

Содержание M359

Отзывы:

Похожие инструкции для M359

Бренды по названию

Популярные бренды