MachMotion 2000 Series Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 33

background image

The 64 general purpose output signals can be controlled from gcode using the mcodes M220 and M221. The gcode

can wait on one of the 64 general purpose inputs to be a certain state with mcode M222. For more information, refer
to the

Mach4 Advanced M-Code Reference

manual.

The following instructions are for configuring a servo spindle as the main spindle on the machine. Some machines, such
as centerless grinders, may be using a servo spindle as an auxiliary spindle or subspindle. See

Auxiliary Spindles

for

more information.

Using Signals In Gcode

M220 S2 D2000 (Turn on Output #2 and wait 2000ms)
M222 S1 T5 (Wait up to 5 seconds for Input #1 to turn on)
M221 S2 D1000 (Turn off Output #2 and wait 1000ms)
M222 S1 T10 I1 (Wait up to 10 seconds for Input #1 to turn off)

Spindle Configuration

Servo Spindle

«
...
20
21
22
23
24
...
»

Содержание 2000 Series


































Отзывы:

Нет отзывов

Похожие инструкции для 2000 Series

Бренд: SAMCHULLY Страницы: 48

Бренд: Datalogic Страницы: 188

Бренд: Valmont Structures Страницы: 8

Бренд: BPW Страницы: 4

Бренд: CHART Страницы: 30

Бренд: WATSON INDUSTRIES Страницы: 27

Бренд: Daikin Страницы: 21

Бренд: Simpro Страницы: 12

Бренд: SCHUNK Страницы: 137

Бренд: Graco Страницы: 2

Бренд: Buhnen Страницы: 14

Бренд: B&G Страницы: 30

IPPCxxB9-RE Series

Бренд: IBASE Technology Страницы: 77

Бренд: SIGLENT Страницы: 7

Бренд: Magikist Страницы: 12

Бренд: SixCase Страницы: 54

Бренд: Panasonic Страницы: 8

Бренд: Panasonic Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды