MacDon R116 Скачать руководство пользователя страница 216

Страница: 216 / 234

214713

208

Revision A

11.6

Torque Specifications

The following tables provide correct torque values for various bolts, cap screws, and hydraulic fittings.

•

Tighten all bolts to torque values specified in charts (unless otherwise noted throughout this manual).

•

Replace hardware with same strength and grade of bolt.

•

Use torque value tables as a guide and periodically check tightness of bolts.

•

Understand torque categories for bolts and cap screws by using their identifying head markings.

Jam nuts

When applying torque to finished jam nuts, multiply the torque applied to regular nuts by f=0.65.

Self-tapping screws

Standard torque is to be used (

NOT

to be used on critical or structurally important joints).

11.6.1

SAE Bolt Torque Specifications

Torque values shown in following tables are valid for non-greased, or non-oiled threads and heads; therefore,
do

NOT

grease or oil bolts or cap screws unless otherwise specified in this manual.

1004958

Figure 11.8: Bolt Grades

A - Nominal Size

B - SAE-8

C - SAE-5

D - SAE-2

Table 11.2 SAE Grade 5 Bolt and Grade 5 Free
Spinning Nut

Nominal

Size (A)

Torque (Nm)

Torque (lbf·ft)

(*lbf·in)

Min.

Max.

Min.

Max.

1/4-20

11.9

13.2

*106

*117

5/16-18

24.6

27.1

*218

*241

3/8-16

7/16-14

1/2-13

106

118

9/16-12

153

170

114

126

5/8-11

212

234

157

173

3/4-10

380

420

281

311

7/8-9

606

669

449

496

1-8

825

912

611

676

REFERENCE

Содержание R116











































































































































































































































Результаты поиска

Содержание R116

Отзывы:

Похожие инструкции для R116

Бренды по названию

Популярные бренды

MacDon R116, Инструкции по разгрузке и сборке

Результаты поиска

Содержание R116

Отзывы:

Похожие инструкции для R116

Бренды по названию

Популярные бренды