MacDon R113 SP Скачать руководство пользователя страница 76

Страница: 76 / 240

215009

Revision A

1018507

Figure 3.94: Left Driveshield

Pull top of driveshield (A) away from the header to open.

NOTE:

For improved access, lift driveshield off the pins at the base
of the shield, and lay the shield on the header.

3.6.2

Closing Driveshields

CAUTION

To reduce the risk of personal injury, do NOT operate the machine without the driveshields in place and secured.

NOTE:

Images shown in this procedure are for the left driveshield

—

the right driveshield is similar.

1018737

Figure 3.95: Left Driveshield

Position driveshield onto pins at base of driveshield
(if necessary).

Push driveshield (A) to engage latch (B).

Check that driveshield is properly secured.

OPERATION

Содержание R113 SP

















































































































































































































































Результаты поиска

Содержание R113 SP

Отзывы:

Похожие инструкции для R113 SP

Бренды по названию

Популярные бренды

MacDon R113 SP, Руководство оператора

Результаты поиска

Содержание R113 SP

Отзывы:

Похожие инструкции для R113 SP

Бренды по названию

Популярные бренды