MacDon R1 FR Series Скачать руководство пользователя страница 51

Страница: 51 / 238

262391

Revision A

3.11

Shutdown Procedure

Follow all the safety procedure and operational instructions given in this manual and in your tractor operator

’

s manual.

DANGER

Before leaving the tractor seat for any reason:

•

Disengage the power take-off.

•

Park on level ground if possible.

•

Lower the header fully.

•

Place all controls in NEUTRAL or PARK.

•

Engage the park brake.

•

Shut down the engine, and remove the key from the ignition.

•

Wait for all movement to stop.

•

Lock tractor

’

s shielding and closures when leaving the machine unattended.

OPERATION

Содержание R1 FR Series















































































































































































































































Результаты поиска

Содержание R1 FR Series

Отзывы:

Похожие инструкции для R1 FR Series

Бренды по названию

Популярные бренды

MacDon R1 FR Series, Руководство оператора

Результаты поиска

Содержание R1 FR Series

Отзывы:

Похожие инструкции для R1 FR Series

Бренды по названию

Популярные бренды