MacDon R1 FR Series Скачать руководство пользователя страница 188 | Manualshive

Страница: 188 / 238

background image

262391

176

Revision A

Installing Driveline Guards

Driveline guards protect components from dirt and debris, and protect operators from moving components. Driveline
guards must installed before operating the machine.

DANGER

To prevent bodily injury or death from the unexpected startup of the machine, always stop the engine and remove the
key from the ignition before leaving the operator

’

s seat.

WARNING

Do NOT operate the machine without the driveline guards in place and securely fastened.

Driveline guards protect both ends of the cross driveline and the primary driveline. To install the driveline guards, follow
these steps:

1.

Lower the header fully.

2.

Shut down the engine, and remove the key from the ignition.

ϭϬϰϯϴϯϲ

A

A

B

Figure 4.178: Driveline Guard

3.

Slide guard (B) toward the driveline ring until both spring clips (A) lock both sides of the guard in place on the
driveline shaft.

IMPORTANT:

If installing a replacement guard, ensure chain is short enough and does

NOT

wrap around the driveline guard.

4.5.3

Primary Driveline

The primary driveline transfers power from the tractor

’

s power take-off (PTO) to the header drive gearbox.

Follow regular lubrication procedures and ensure all drivelines are installed as instructed. For instructions, refer to

Maintenance Schedule/Record, page 72

MAINTENANCE AND SERVICING

«
...
186
187
188
189
190
...
»

Содержание R1 FR Series















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для R1 FR Series

Бренд: OMCA Страницы: 72

Бренд: Barko Hydraulics Страницы: 92

Бренд: Parker Страницы: 54

Бренд: Tascam Страницы: 27

Бренд: Jay-Lor Страницы: 72

Бренд: MacDon Страницы: 198

Бренд: M-Triangel Страницы: 6

Бренд: Rapid Technic Страницы: 152

Бренд: Dawn Страницы: 8

Бренд: BACtrack Страницы: 13

Бренд: Badgematic Страницы: 28

Бренд: BACtrack Страницы: 2

Бренд: MADRIX Страницы: 28

Бренд: BACTcontrol Страницы: 28

Бренд: Backyard Products Страницы: 98

Бренд: p-light Страницы: 28

Бренд: Hanna Instruments Страницы: 2

Бренд: Hanna Instruments Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды