MacDon R1 FR Series Скачать руководство пользователя страница 179

Страница: 179 / 238

262391

167

Revision A

1016453

Figure 4.159: Cutterbar Spindle

11. Use the Safecut spindle-nut wrench to remove nut (A).

1016456

Figure 4.160: Cutterbar Spindle

12. Remove shear pins (B).

IMPORTANT:

NOT

damage the pin bore on the pinion.

13. Remove hub (A).

14. Check the nut and the hub for damage. Replace them if

necessary.

Installing Cutterbar Spindle Shear Pin

Ensure that the grooves in the shear pin are parallel to the cutterbar when it is installed into the spindle.

DANGER

To prevent injury or death from the unexpected start-up or fall of a raised machine, always stop the engine and remove
the key from the ignition before leaving the operator

’

s seat or making adjustments to the machine. If the rotary disc

header is raised, always close the lock-out valves, and place blocks under the header. Never work on or beneath an
unsupported header.

DANGER

Ensure that all bystanders have cleared the area.

WARNING

Exercise caution when working around the blades. Blades are sharp and can cause serious injury. Wear gloves when
handling blades.

Position the rotary disc header at an appropriate height for the task.

Shut down the engine, and remove the key from the ignition.

MAINTENANCE AND SERVICING

Содержание R1 FR Series















































































































































































































































Результаты поиска

Содержание R1 FR Series

Отзывы:

Похожие инструкции для R1 FR Series

Бренды по названию

Популярные бренды

MacDon R1 FR Series, Руководство оператора

Результаты поиска

Содержание R1 FR Series

Отзывы:

Похожие инструкции для R1 FR Series

Бренды по названию

Популярные бренды