MacDon R1 FR Series Скачать руководство пользователя страница 146 | Manualshive

Страница: 146 / 238

background image

262391

134

Revision A

Removing Inboard Rock Guards

Remove any damaged or worn rock guards to maximize the life of the cutting blades.

DANGER

To prevent injury or death from the unexpected start-up or fall of a raised machine, always stop the engine and remove
the key from the ignition before leaving the operator

’

s seat or making adjustments to the machine. If the rotary disc

header is raised, always close the lock-out valves, and place blocks under the header. Never work on or beneath an
unsupported header.

DANGER

Ensure that all bystanders have cleared the area.

WARNING

Exercise caution when working around the blades. Blades are sharp and can cause serious injury. Wear gloves when
handling blades.

1.

Position the rotary disc header at an appropriate height for the task.

2.

Shut down the engine, and remove the key from the ignition.

3.

If the rotary disc header is raised:

a.

Place blocks under each end, or just inside each end, of the cutterbar.

b.

Lower the rotary disc header onto the blocks.

c.

Shut down the engine, and remove the key from the ignition.

d.

Close the auxiliary lift cylinder lock-out valves. For instructions, refer to

3.2.1 Locking and Unlocking Auxiliary Lift

Cylinders, page 22

.

1003622

A

Figure 4.95: Inboard Rock Guards

4.

Remove two hex head screws, washers, and lock nuts (A).

MAINTENANCE AND SERVICING

«
...
144
145
146
147
148
...
»

Содержание R1 FR Series















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для R1 FR Series

Бренд: Keithley Страницы: 36

Бренд: Rain-Flo Irrigation Страницы: 16

Бренд: idiag Страницы: 10

Бренд: Bandit Страницы: 136

Versaflo S Series

Бренд: 3M Страницы: 11

DBI Sala EXOFIT

Бренд: 3M Страницы: 32

Бренд: 3M Страницы: 8

Бренд: Accurate Bio-Medical Technology Страницы: 35

Бренд: made for movement Страницы: 51

Бренд: Rain-Flo Irrigation Страницы: 16

Бренд: jcb Страницы: 41

Бренд: HALDER Страницы: 2

Бренд: Hakko Electronics Страницы: 16

Бренд: IFM Страницы: 175

Бренд: IFM Страницы: 5

Бренд: Land Pride Страницы: 38

NI VISION PCI-8254R

Бренд: National Instruments Страницы: 13

NI VISION PCI-8254R

Бренд: National Instruments Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды