MacDon D65 Скачать руководство пользователя страница 32

Страница: 32 / 110

214328

Revision A

3.2

Attaching Cam Arms

To attach reel cam arms, follow these steps:

Figure 3.14: Disconnected Cam Links and
Shipping Wire

Rotate reel manually to access the tine tube cranks (A)
that are not connected to cam links.

Remove shipping wires one row at a time.

NOTE:

To prevent reel cams from rotating over center, remove
shipping wires one row at a time.

Figure 3.15: Hardware Bag Right Reel

Remove bag of hardware (A) from tine bar. It contains
hardware for cam links and endshields.

Figure 3.16: Tine Bar Crank and Link

Rotate tine tube crank (A) and position link (B) so
attachment holes in bar crank are aligned with hole
in link.

Install bolt (C) in link, and position shim (D) on bolt so
that shim is between link and tine bar crank.

NOTE:

Bolts are precoated with Loctite

, so no further locking

method is required.

Realign link (B) and tine bar crank (A), and thread in
bolt (C).

Repeat for remaining tine bars and torque bolts to
165 Nm (120 lbf·ft).

ASSEMBLING HEADER

Содержание D65















































































































Результаты поиска

Содержание D65

Отзывы:

MacDon D65, Инструкция по сборке, Страница: 32 / 110

Результаты поиска

Содержание D65

Отзывы: