Maaselan Kone Oy Hakki Pilke 37 Series Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 57

background image

28

Original

Version 1-2011

4.6 Operating and adjusting the input conveyor

The  input  conveyor  is  activated
when the cutting lever is moved up
from its initial position. Note! In the
Easy  model,  the  conveyor  can  be
activated  with  the  control  lever  B
(in  Figure  20)  by  pushing  the  lever
to the up/right position.

The conveyor stops when the
cutting lever is lowered to the
initial position or when wood
is cut by pushing the lever
downwards. In the Easy
model, the conveyor stops
when the control lever B is
restored to the centre
position or when the lever is
pulled backwards.

To reverse the input conveyor belt,
press  the  reverse  pedal  E.  In  the
Easy  model,  the  same  can  be  done
by moving the control lever B to the
up/left position.

«
...
26
27
28
29
30
...
»

Содержание Hakki Pilke 37 Series


























































Отзывы:

Нет отзывов

Похожие инструкции для Hakki Pilke 37 Series

Бренд: Wallenstein Страницы: 45

Бренд: Scheppach Страницы: 152

SPLITMASTER S401625UB

Бренд: SpeeCo Страницы: 17

Бренд: Ariens Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды