manualshive.com logo in svg

M7 SPEED 70-530200, Руководство по установке

Поделиться
Скачать
M7 SPEED 70-530200 Скачать руководство пользователя страница 1

 

September 16, 2020 

 Page 1 of 12 

 

Installation Guide

 

Gen 3 Countryman/Clubman Lift Kit 

Part # 70-530200   (2.5” Lift) 

 

 

M

7 Speed engineers and manufactures the highest quality and best fitting MINI Cooper accessories and performance parts available 

anywhere on Planet Earth!  Please inspect your parts when you receive them to verify everything is included and no damage has 

happened during shipment. Read these instructions completely BEFORE attempting to install this product.  If you are not confident you 

can do the work described or do not have the tools or skills necessary please contact a local M7 dealer (listed on our website 

www.m7speed.com

) or a local MINI repair shop or automotive accessory installation center to perform this work. We acknowledge not 

everything is perfect but we work very hard every day to improve our products and make installations easier.  If you have any 

comments please contact M7 Customer Service directly at 704-663-0094.  We encourage and welcome any and all criticism, comments 

or product reviews. Thank you. 

NOTE: 

 

THE INSTALLATION OF THIS GEN 3 MINI COOPER LIFT KIT REQUIRES ADVANCED MECHANICAL SKILLS AND 

TOOLS NOT TYPICALLY FOUND IN A D.I.Y. TOOL KIT.  WE STRONGLY RECOMMEND THAT AN EXPERIENCED 

MECHANIC OR INSTALLATION SHOP PERFORM THE INSTALLATION OF THIS KIT. 

NOTE: 

 

THIS GUIDE ONLY OUTLINES THE MAJOR STEPS REQUIRED TO PERFORM THE INSTALLATION. STANDARD 

INDUSTRY PRACTICES AND GENERAL KNOWLEDGE OF VEHICLE ASSEMBLY AND DISASSEMBLY ARE NOT 

DETAILED IN THIS GUIDE.  THE INSTALLER ASSUMES ALL RESPONSIBILITY AND LIABILITY FOR ANY 

DAMAGE ENCOUNTERED WHILE INSTALLING THESE PARTS. IN ADDITION THE INSTALLER ASSUMES ALL 

RESPONSIBILITY AND LIABILITY FOR ANY DAMAGES OR INJURY THAT ARE A DIRECT OR INDIRECT RESULT 

OF IMPROPER INSTALLATION AND/OR POOR WORKMANSHIP. 

Содержание 70-530200













Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды