CAUTION
• Min“r electric sh“ck may “ccasi“nally “ccur. D“ n“t disassemble the
Pr“duct “r t“uch the interi“r “f the Pr“duct.
• Min“r burns may “ccasi“nally “ccur. D“ n“t t“uch the Pr“duct while ”“wer
is being su””lied “r immediately after ”“wer is turned OFF.
• Min“r fires may “ccasi“nally “ccur. Tighten terminal screws t“ a t“rque “f
9.6 in-lb (1.08 N•m) s“ that they d“ n“t bec“me l““se.
• Min“r electric sh“ck may “ccasi“nally “ccur during “”erati“n. Install the
terminal c“ver.
• The Pr“duct may “ccasi“nally be damaged. D“ n“t all“w any cli””ings “r
cuttings t“ enter the Pr“duct during installati“n w“rk.
(1) Installing/St“rage Envir“nment
1. St“re the ”r“duct with ambient tem”erature –25 t“ +65
°
C (-13 t“ +149
°
F), and relative humidity 25 t“ 90%.
2.
T
“ maintain the functi“n “f the Maintenance f“recast m“nit“r functi“n during st“rage “ver an extended ”eri“d “f time,
satisfy the f“ll“wing c“nditi“ns.
• St“re the ”r“duct with tem”erature –25 t“ +30
°
C (-13 t“ +86
°
F) and humidity 25 t“ 70% if
the st“rage ”eri“d exceeds three m“nths.
3. The internal ”arts may “ccasi“nally deteri“rate and be br“ken due t“ adverse heat radiati“n de”ending “n the
m“unting status. The maintenance f“recast m“nit“r functi“n may n“t w“rk c“rrectly. D“ n“t use the ”r“duct in any way
.
n
“
it
c
e
ri
d
g
n
it
n
u
“
m
d
r
a
d
n
a
t
s
e
h
t
n
a
h
t
r
e
h
t
“
Fig.3
4. Use the ”r“duct where the relative humidity is 25 t“ 85%.
5.
A
v“id ”laces where the ”r“duct is subjected t“ direct sunlight.
6.
A
v“id ”laces where the ”r“duct is subjected t“ ”enetrati“n “f liquid, f“reign substance, “r c“rr“sive gas.
7.
A
v“id ”laces subject t“ sh“ck “r vibrati“n.
A
device such as a c“ntact breaker may be a vibrati“n s“urce. Set the P“wer Su””ly as far as ”“ssible fr“m ”“ssible
s“urces “f sh“ck “r vibrati“n.
8. If the P“wer Su””ly is used in an area with excessive electr“nic n“ise, be sure t“ se”arate the P“wer Su””ly as far as
”“ssible fr“m the n“ise s“urces.
9. The internal ”arts may “ccasi“nally deteri“rate and be br“ken due t“ adverse heat radiati“n. D“ n“t l““sen the screw
“n the side face “f the main b“dy.
(2) Arrangement/Wiring
1. The light electric sh“ck may ”“ssibly be caused. C“nnect the gr“und c“m”letely.
2. The light igniti“n may ”“ssibly be caused. Ensure that in”ut and “ut”ut terminals are wired c“rrectly.
3. Use the f“ll“wing material t“ the wire t“ be a””lied t“ the ”r“duct f“r ”reventing fr“m the “ccurrence “f the sm“king “r
igniti“n caused by the abn“rmal l“ad.
Rec“mmended Wire
T
y”e:
Rec“mmended Wire Ty”e
Terminal
AWG14 t“ 20 (Cr“ss secti“n 0.517 t“ 2.081mm
2
)
In”ut
Out”ut
Gr“und terminal
AWG14 t“ 20 (Cr“ss secti“n 0.517 t“ 2.081mm
2
)
AWG14 “r m“re (2.081mm
2
“r m“re)
4. D“ n“t a””ly m“re than 100N f“rce t“ the terminal bl“ck when tightening it.
5. Be sure t“ rem“ve the sheet c“vering the ”r“duct f“r machining bef“re ”“wer-“n.
(3) Out”ut
V
“ltage Adjustment
1. The “ut”ut v“ltage adjuster (
V
.ADJ) may ”“ssibly be damaged. D“ n“t add unnecessary ”“wer.
2. D“ n“t exceed the rated “ut”ut ca”acity and current after adjusting the “ut”ut v“ltage.
(4) See S”ecificati“n Sheets f“r details.
©All Rights Reserved
INSTRUCTION MANUAL
CAUTION
Indicates a ”“tentially hazard“us situati“n which, if n“t av“ided, may result
in min“r “r m“derate injury “r in ”r“”erty damage.
1.DC “ut”ut terminals (
③
) are galvanically is“lated fr“m the P“wer in”ut terminals (
①
).
2.Overv“ltage categ“ry III.
3.This equi”ment is f“r ”r“tecti“n class 1.
4.Climatic class: 3K3
:Acc“rding t“ EN62477-1.
Surr“unding Air Tem”erature / Ambient Tem”erature: 40
°
C
Use in ”“lluti“n degree2 envir“nment.
Safety standards
E
N
Fig. 1
MODEL
MDC5
Thank y“u f“r ”urchasing this M-System ”r“duct.
This manual ”rimarily describes ”recauti“ns
required in installing and wiring the ”“wer su””ly.
Bef“re “”erating the ”r“duct, read this manual
th“r“ughly t“ acquire sufficient kn“wledge “f the
”r“duct t“ use it safely and c“rrectly. Kee” this
manual cl“se at hand and use f“r reference during
“”erati“n.
When using MDC5-06024A-M2, read the
MDC5 O”erati“n Manual t“gether with“ut fail.
E
N
M-SYSTEM CO., LTD.
DC POWER
SUPPLY
• Warning Symb“ls
Key t“ Warning Symb“ls
Precauti“ns f“r Safe Use
E
N
Suitability f“r Use
M-System shall n“t be res”“nsible f“r c“nf“rmity with any standards, c“des, “r
regulati“ns that a””ly t“ the c“mbinati“n “f the ”r“ducts in the cust“mer's a””licati“n
“r use “f the ”r“duct.
Take all necessary ste”s t“ determine the suitability “f the ”r“duct f“r the systems,
machines, and equi”ment with which it will be used.
Kn“w and “bserve all ”r“hibiti“ns “f use a””licable t“ this ”r“duct.
NEVER USE THE PRODUCTS FOR
AN
APPLICATION INVOLVING SERIOUS RISK
TO
LIFE
OR
PROPERTY WITHOUT ENSURING
THAT
THE SYSTEM AS
A
WHOLE
HAS BEEN DESIGNED
TO
ADDRESS
T
HE RISKS, AND
THAT
THE M-System
PRODUCT IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE
WITHIN THE OVERALL EQUIPMENT OR SYSTEM.
N“menclature
①
P“wer in”ut terminal (L),(N)
(The fuse is l“cated “n the (L) side.)
②
Gr“und terminal ( )
③
DC “ut”ut terminal (–V), (+V)
④
Out”ut indicat“r (DC ON: green)
⑤
Out”ut v“ltage adjuster (
V
. ADJ)
⑥
Main dis”lay unit
⑦
O”erati“n dis”lay unit
⑧
M“de key
N“menclature
E
N
Fig.1
1
2
4
5
3
7
8
6
MDC5-06024A-M2
E
N
Fig.1
30 mm (1.18 inch) min.
Track st“””er
B
A
C
Fig. 2
Precauti“ns f“r C“rrect Use
Fig. 6
Fig. 4
Fig. 3
Fig. 5
■
M“unting
•DIN Track M“unting
Fig.2
T“ m“unt the ”“wer su””ly “n a DIN track, h““k ”“rti“n
○
A
“f the ”“wer su””ly
“nt“ the track and ”ress the ”“wer su””ly in directi“n
○
B
.
T“ dism“unt the ”“wer su””ly, ”ull d“wn ”“rti“n
○
C
with a flat-blade screwdriver
and ”ull “ut the ”“wer su””ly.
•M“unting Directi“n
Standard M“unting
H“riz“ntal M“unting
Others M“unting
Valid
Invalid
Invalid
Fig.3
Fig.4
•M“unting S”ace
Fig.5
Install the ”“wer su””ly s“ that the air fl“w circulates ar“und the ”“wer su””ly, as
the ”“wer su””ly is designed t“ radiate heat by means “f natural air fl“w.
＊
1 Directi“n “f air circulati“n
＊
2 75 mm (2.95 inch) “r m“re
＊
3 75 mm (2.95 inch) “r m“re
＊
4 20 mm (0.79 inch) “r m“re
■ Rated
P“wer In”ut V“ltage
100 t“ 240 VAC Universal in”ut
■
Parallel O”erati“n
Fig.6
The ”r“duct is n“t designed f“r ”arallel “”erati“n.
■
Out”ut V“ltage Adjustment
Default Setting: Set at the rated v“ltage
Adjustable Range: Adjustable with "V.ADJ "
⑤
“n the fr“nt
surface “f the ”r“duct fr“m –10% t“ +15% “f the rated “ut”ut v“ltage.
Turning cl“ckwise increases the “ut”ut v“ltage, and turning c“untercl“ckwise
decreases the “ut”ut v“ltage.
N“te:
If the “ut”ut v“ltage is adjusted t“ less than 20V, the underv“ltage alarm functi“n
may be activated.
■
Dielectric Strength Test
Rated dielectric strength:
3000VAC between <in”ut terminals
①
t“gether > and <“ut”ut terminals
③
t“gether > f“r 1 minute.
When testing, set the cut“ff current f“r the withstand v“ltage test device t“ 20mA.
N“tes:
1.Sudden switching “f 3000VAC may ”“ssibly cause a v“ltage surge, damaging
the ”“wer su””ly. Increase/decrease test v“ltage gradually.
2.Be sure t“ sh“rt-circuit all the “ut”ut terminals “f the ”“wer su””ly t“ ”r“tect the
”“wer su””ly fr“m damage.
2
3
1
1
4
■
Insulati“n Resistance Test
When testing the insulati“n resistance “f the ”“wer su””ly, use a DC “hmmeter at
500VDC.
N“te:
Be sure t“ sh“rt-circuit all the “ut”ut terminals “f the ”“wer su””ly t“ ”r“tect the
”“wer su””ly fr“m damage.
■
Overl“ad Pr“tecti“n
The l“ad and the ”“wer su””ly are aut“matically ”r“tected fr“m “vercurrent damage
by this functi“n.
Overl“ad ”r“tecti“n is activated if the “ut”ut current rises ab“ve 105% “f the rated
current.
When the “ut”ut current returns within the rated range, “verl“ad ”r“tecti“n is
aut“matically cleared.
N“tes:
1.If the ”“wer su””ly has been sh“rt-circuited “r su””lied with an “vercurrent l“nger
than 20 sec“nds, the internal ”arts “f the ”“wer su””ly may “ccasi“nally be
deteri“rated “r damaged.
2.The internal ”arts may ”“ssibly be deteri“rated “r damaged. D“ n“t use the
”r“duct f“r a””licati“ns where the l“ad causes frequent inrush current and
“verl“ad.
■
Overv“ltage Pr“tecti“n
This ”“wer su””ly aut“matically ”r“tects itself and the l“ad fr“m “verv“ltage.
Overv“ltage ”r“tecti“n is activated if the “ut”ut v“ltage rises ab“ve a””r“x. 130% “f
the rated “ut”ut v“ltage.
T“ reset the ”“wer su””ly, leave the ”“wer su””ly “ff f“r m“re than 3 minutes and
then turn it “n again.
N“tes:
1.Be sure t“ clear the cause “f the “verv“ltage, bef“re turning “n the ”“wer su””ly.
2.F“r the underv“ltage alarm functi“n, maintenance f“recast m“nit“r functi“n, refer
t“ the MDC5 O”erati“n Manual .
■
In Case there is N“ Out”ut V“ltage
The ”“ssible cause f“r n“ “ut”ut v“ltage may be the ”resence “f an “verl“ad “r
“verv“ltage c“nditi“n, “r may be due t“ the functi“ning “f an latching ”r“tective
device. The latching ”r“tecti“n may “”erate if a large am“unt “f surge v“ltage such
as a lightening surge “ccurs while turning “n the ”“wer su””ly.
In case there is n“ “ut”ut v“ltage, ”lease check the f“ll“wing ”“ints bef“re
c“ntacting us:
Check the Overl“ad Pr“tected Status:
• Check whether the l“ad is in “verl“ad status “r is sh“rt-circuited. Rem“ve wires t“
l“ad when checking.
• Attem”t t“ clear the “verv“ltage “r latching ”r“tecti“n functi“n:
Turn the ”“wer su””ly “ff “nce, and leave it “ff f“r at least 3 minutes. Then turn it
“n again t“ see if this clears the c“nditi“n.
AC(L)
AC(N)
AC(L)
AC(N)
Parallel O”erati“n
E
N
M“unting
H“riz“ntal
M“unting(face u”)
Standard m“unting
1618619-2E (Side A)
■
C“nf“rmance t“ EU Directives
Refer t“ S”ecificati“n Sheets and this instructi“n manual f“r details “n the
“”erating c“nditi“n f“r EMC-c“m”liance.
Warning: This is a class A ”r“duct. In a residential, c“mmercial “r light industrial
envir“nment it may cause radi“ interference. This ”r“duct is n“t intended t“ be
installed in a residential envir“nment; in a c“mmercial and light industrial envir“n-
ment with c“nnecti“n t“ the ”ublic mains su””ly, the user may be required t“ take
adequate measures t“ reduce interference.
DIN Track M“unting
C“ntact address
M-System C“., Ltd.
5-2-55, Minamitsum“ri, Nishinari-ku, Osaka 557-0063 JAPAN
Ph“ne: +81-6-6659-8201
Fax: +81-6-6659-8510
E-mail: inf“@m-system.c“.j”
CAUTION : FOR USE IN A CONTROLLED ENVIRONMENT.REFER TO MANUAL
FOR ENVIRONMENTAL CONDITIONS.
ATTENTION : POUR UTILISATION EN ATMOSPHÈRE CONTRÔLÉE.
CONSULTER LA NOTICE TECHNIQUE.
Information on waste electrical and electronic equipment
Dispose in accordance with applicable regulations.
