M-system 47DM Скачать руководство пользователя | Manualshive

Страница: 61 / 238

background image

61

47DM OPERATING MANUAL EM-9510-B Rev.6

4. OPERATION

Make sure that 0.000 – 100.000% is correctly indicated according to the input 2 – 8 kΩ provided with the total resistance 10
kΩ. The operation without using external control signals including the event trigger input is described here.

IMPORTANT

Before operating, make sure that the wiring is correct, the input and the power supply are within the specification range.

1

Apply 2 kΩ input (0%) and make sure that 0.000% is indicated.

NOTE

■

WHEN THE FOLLOWING IS INDICATED…

• When ‘S.ERR’ is indicated, the input is not applied correctly. Check the input

wiring, equipment and signal.  When the SD indicates ‘UNDER’, the input signal
is under the specification voltage/current.  And when the SD indicates ‘OVER’, the
input is over the specification voltage/current.

• When the indication is shifted with ‘FZ’ and/or ‘TZ’ indicators on, the Forced Zero

or Tare Adjustment is being executed. Cancel the Forced Zero and Tare Adjust-
ment. (Refer to 25. FORCING THE PRESENT DISPLAY VALUE TO ZERO.)

■

WHEN THE INDICATION DOES NOT CHANGE…

• MAX or MIN value is indicated with ‘Max’ or ‘Min’ indicator on. Cancel the MAX/

MIN Value Display mode. (Refer to 26. RETAINING MAX AND MIN VALUES.)

■

ALARM INDICATORS

• The status of the alarm indicators depends on the alarm setpoints. The above display examples show ‘P’ indicator on.

■

DISPLAY COLOR

• The main display color depends on the settings of the display color and setpoints.

2

Apply 5 kΩ input (50%) and make sure that 50.000% is indi-

cated.

3

Apply 8 kΩ input (100%) and make sure that 100.000% is indi-

cated.

*

1 Display depends on the settings and input.

Blinking

Blinking

«
...
59
60
61
62
63
...
»

Содержание 47DM















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 47DM

Бренд: Hammond Страницы: 754

Бренд: J.P. Instruments Страницы: 9

Бренд: J.ASSY Страницы: 13

Бренд: QMI Страницы: 54

Бренд: Keysight Страницы: 92

Бренд: Technoline Страницы: 1

Бренд: Hanna Instruments Страницы: 2

Бренд: Magnetrol Страницы: 48

Бренд: TDI Страницы: 32

Бренд: OrienTek Страницы: 2

Бренд: Avtech Страницы: 40

G-TRAN CCMT-D Series

Бренд: Ulvac Страницы: 2

Grason-Stadler GSI 17 1717-9700

Бренд: Welch Allyn Страницы: 104

Бренд: Efergy Страницы: 24

Бренд: HW Group Страницы: 12

COOL-US CU-935A

Бренд: Y?lmaz So?utma Страницы: 16

Total Station KTS-462R10L

Бренд: Kolida Страницы: 191

Бренд: QEED Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды