M-system 47DM Скачать руководство пользователя

Страница: 162 / 238

162

47DM OPERATING MANUAL EM-9510-B Rev.6

20.1 EVENT TRIGGER MODE

20.1.1 OPERATING PROCEDURE

NOTE

The following figures are display examples. The displays
depend on the settings.

Hold down Alarm/

↓

and Scale/

↑

buttons at once for 3 seconds

or more to move on to Advanced Setting Mode.

• The event trigger mode is indicated.
• The SD indicates ‘EVENT’.

Press Shift and Up buttons to select the event trigger mode.

• Select one among ‘NORMAL’, ‘S-HLD’, ‘P-HLD’, ‘B-HLD’ and ‘PP-

HLD’.

Press Alarm/

↓

or Scale/

↑

button to apply the new setting.

• And the next parameter setting is indicated.

NOTE

• Press Alarm/

↓

button, and the ON timing delay will be indicated (‘ON-TDLY’ on the SD), or the startup timer will be indi-

cated (‘STR-TMR’ on the SD) with the event trigger mode set to “normal”.

• Press Scale/

↑

button, and the firmware version indication will be indicated (‘FRM-VER’ on the SD).

1,3

Blinking

Содержание 47DM















































































































































































































































Результаты поиска

Содержание 47DM

Отзывы:

Похожие инструкции для 47DM

Бренды по названию

Популярные бренды

M-system 47DM, Руководство по эксплуатации

Результаты поиска

Содержание 47DM

Отзывы:

Похожие инструкции для 47DM

Бренды по названию

Популярные бренды