M-system 47DM Скачать руководство пользователя

Страница: 129 / 238

129

47DM OPERATING MANUAL EM-9510-B Rev.6

11.2 AVERAGING TIME

11.2.1 OPERATING PROCEDURE

NOTE

The following figures are display examples. The displays
depend on the specifications and settings.

Hold down Alarm/

↓

and Scale/

↑

buttons at once for 3 seconds

or more to move on to Advanced Setting Mode.

• The averaging type is indicated.
• The SD indicates ‘AVE-TP’.

NOTE

With the I/O option code ‘6’ or ‘A’, the event trigger mode is indicated (‘EVENT’ on the SD).

Press Alarm/

↓

or Scale/

↑

button to go to the averaging time

setting.

• The averaging time is indicated.
• The SD indicates ‘AVE-N’.

Press Shift and Up buttons to select the averaging time.

• Select one among ‘OFF’, ‘2’, ‘4’, ‘8’, ‘16’, ‘32’, ‘64’, ‘128’, ‘256’ and ‘512’.

1,2,

4,5

1,2,

4,5

Blinking

Содержание 47DM















































































































































































































































Результаты поиска

Содержание 47DM

Отзывы:

Похожие инструкции для 47DM

Бренды по названию

Популярные бренды

M-system 47DM, Руководство по эксплуатации

Результаты поиска

Содержание 47DM

Отзывы:

Похожие инструкции для 47DM

Бренды по названию

Популярные бренды