M/A-Com Orion Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 80

background image

38

Menu Selection

Press

M

and then use the

,

.

control to scroll through the selections

until

SYS SCAN

is displayed. Then press

M

to toggle the System Scan

state. The

SYSC ON

or

SYSC OFF

display message is displayed for two

seconds to show the new state.

Pre-Programmed Keypad Key

Press the pre-programmed key and the

SYSC ON

or

SYSC OFF

display

message is displayed for two seconds to show the new state.

GROUP SCAN OPERATION

Only Groups that are part of the radio's scan list may be scanned. Groups are
added to the scan list on a per system basis by PC Programming, the radio
keypad, or both, depending upon programming. This scan list may be changed
by the user from the keypad unless programmed otherwise. Each system's
group scan list is retained in memory when the radio is turned OFF. The Orion
mobile radio may also be programmed to provide Trunked Priority Group
Scan capability, which operates similar to priority scan in Conventional mode.

The following is a description of PC-Programmable scan features that should
be helpful in understanding the Group Scan Operation of the radio:

Scan Hang Time

- the delay time the radio waits before resuming scan after

the push-to-talk is released or after the carrier has dropped a channel.

TX Select

- the group the radio will transmit on while scanning. The radio is

programmed to transmit on either the scanned group or the selected group.

Scan List (privileges)

- this feature allows or prohibits scan list changes by the

user.

P1 Programming

- priority group programming is accomplished by one (and

only one) of three methods:

1.

From the keypad, where the Priority programming is not fixed and
does not follow the selected channel.

2.

Priority 1 group programming follows the selected channel.

3.

Priority 1 group programming is fixed during PC Programming and
cannot be changed by the user.

P1 Always Scan

- determines if the Priority 1 Group will always be scanned,

regardless of the scan state set by the user.

«
...
36
37
38
39
40
...
»

Содержание Orion

















































































Отзывы:

Нет отзывов

Похожие инструкции для Orion

Бренд: P1PE Страницы: 28

Бренд: Oxygen Страницы: 15

Бренд: Maxcom Страницы: 2

Бренд: Hytera Страницы: 33

Бренд: Polaroid Страницы: 29

Бренд: Zamel Страницы: 60

BR-Klassik DIR3121M

Бренд: Hama Страницы: 45

Бренд: PRESERVATECH Страницы: 17

Бренд: ILX Lightwave Страницы: 55

Бренд: Eton Страницы: 40

Бренд: Century Mark IV Страницы: 6

Бренд: Toyama Страницы: 52

Бренд: Curtis Страницы: 1

Бренд: Curtis Страницы: 28

Бренд: ION Страницы: 10

Бренд: ION Страницы: 33

Бренд: Winco Страницы: 18

Бренд: Mitsubishi Electric Страницы: 182

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды