LYNXTechnik C MX 5710 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 36

background image

C MX 5710 Reference Manual. Rev 1.0

Page 13 of 36

Installation

If this module was supplied as part of a system it is already installed in the rack
enclosure. If the module was supplied as a field upgrade please follow the
installation procedure below.

NOTE

Observe static precautions when handling card.

Please see ESD warnings on Page 7.

This module has a single width rear connection panel. Up to ten C MX 5710
modules can be accommodated in a single Series 5000 2RU rack frame.

Each Card Module is supplied with a rear connection panel and mounting
screws. Please follow the procedure below for the installation of the card module
into the Series 5000 Card Frame.

We recommend you power the rack down before installing any additional
modules into an existing card frame.

1. Select a free slot space in the card frame where the CardModule will be

located.

2. Remove the blank connection panels from the rear of the rack (if fitted)
3. Install the rear connection panel using the screws supplied. Do not tighten

the screws fully

4. Slide the card module into the card frame and carefully check the

CardModule  connects  to  the  rear  connection  plate.  The  card  should  fit
easily  and  should  not  require  excessive  force  to  insert  -  if  you  feel  any
resistance,  there  could  be  something  wrong  with  the  rear  connection
panel location.

Do not

try and force the connection this may damage the

connectors. Remove the rear connection panel and check alignment with
the CardModule.

5. Insert and remove the CardModule a few times to ensure correct

alignment and then tighten the two screws to secure the rear connection
plate.

6. Power up the rack and check the module

LED’s. Check the module is

automatically logged into the control system device tree.

(It may take a

few seconds for the control system to “discover” the new module)

NOTE:

The use of the optional control system is

mandatory

for the control and

setup of this module. If you do not have the control system, then please
contact your LYNX representative for details on how to upgrade your
installation with the LYNX control system.

«
...
11
12
13
14
15
...
»

Содержание C MX 5710





































Отзывы:

Нет отзывов

Похожие инструкции для C MX 5710

LIMETREE USB-DAC

Бренд: Lindemann Страницы: 24

Бренд: Konig Страницы: 30

Бренд: K&S BASIC Страницы: 17

Бренд: Kohler Страницы: 44

Бренд: American Audio Страницы: 2

Бренд: N-Tron Страницы: 40

PowerClean Salt Econ

Бренд: CMP Страницы: 24

Бренд: Nagra Страницы: 18

ECO Inverter+ 7

Бренд: Oilon Страницы: 58

SINEMASTER IG4300

Бренд: Kipor Страницы: 50

Бренд: Hagstrom Страницы: 36

SureSine 1000 W

Бренд: Morningstar Страницы: 66

blueplanet 87.0 TL3

Бренд: Kaco Страницы: 115

Varispeed V7 Series

Бренд: YASKAWA Страницы: 34

Бренд: Sveon Страницы: 45

Бренд: Midian Electronics Страницы: 4

Бренд: Leader Electronics Corp. Страницы: 13

Бренд: Micno Страницы: 29

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды